KMD-201AA KMD-201AWA - Hoshizaki

More documents

Recommendations

Info

7) Remove the two mounting screws.8) Install the new valve in the reverse order of the removal procedure.9) Open the water supply tap.10) Plug in the icemaker or connect the power source.11) Check for leaks.12) Refit the panels in their correct positions.14. WATER TANK1) Remove the front panel, then remove the front insulation2) Loosen the two thumbscrews securing the Pump Motor Bracket3) Move the control switch to the "SERVICE" position. Move the service switch to the"DRAIN" position.4) Let the icemaker run for 2 minutes.5) Move the control switch to the "OFF" position.6) Turn off the power supply.7) Disconnect the Pump Motor and Float Switch connector from the side of the control box.8) Keep pushing up the snapping tab at the right side of the Pump Motor Bracket.9) Pull out the Water Tank, Cube Guide, Pump Motor Bracket, Pump Motor and Float Switchtogether.41
10) Install the new water tank in the reverse order of the removal procedure.11) Refit the panels in their correct positions.12) Turn on the power supply.15. FLOAT SWITCH1) Remove the Pump Motor Bracket. See "V. 14. WATER TANK."2) Pull up the Pump Motor Bracket from the Water Tank.3) Flip over the Pump Motor Bracket assembly, then twist off the Float Switch and pull outtowards you.42
Page 1 and 2: NO. F037-775ISSUED: JUN. 15, 2009RE
Page 3 and 4: [a] NO ICE PRODUCTION -------------
Page 6 and 7: II. GENERAL INFORMATION1. CONSTRUCT
Page 9 and 10: [e] NORMAL HARVEST CYCLELEDs 5, 6,
Page 11 and 12: 3. CONTROL BOARD* A HOSHIZAKI exclu
Page 13 and 14: [b] FEATURESa) Maximum Water Supply
Page 15 and 16: [c] CONTROLS AND ADJUSTMENTSa) Defa
Page 17 and 18: f) Freeze Timer (S1 dip switch 9 &
Page 19 and 20: 5. FLOAT SWITCH[a] EXPLANATION OF O
Page 21 and 22: 7. SWITCHESTwo different control sw
Page 23 and 24: 2. WIRING DIAGRAM20
Page 25 and 26: IV. SERVICE DIAGNOSIS1. 10-MINUTE D
Page 27 and 28: 2. DIAGNOSTIC CHARTS[a] NO ICE PROD
Page 29 and 30: 1. See "II. 3. [d] ControlBoard Che
Page 31 and 32: 1. See "II. 3. [d] ControlBoard Che
Page 33 and 34: V. REMOVAL AND REPLACEMENT1. SERVIC
Page 35 and 36: 2. BRAZINGNote: All brazing connect
Page 37 and 38: 5) Remove the Drier using brazing e
Page 39 and 40: 9) Evacuate the system, and charge
Page 41 and 42: 19) Turn on the power supply.9. ADJ
Page 43: 7) Remove the Hose Band connecting
Page 47 and 48: 8) Connect the bin control connecto
Page 49 and 50: 5) Refit the removed parts in the r
Page 51 and 52: 2) Install the new Run Capacitor in
Page 53 and 54: VI. CLEANING AND MAINTENANCE INSTRU
Page 55 and 56: g. Wipe down the float switch housi
Page 57 and 58: [a] STAINLESS STEEL EXTERIORTo prev
Page 59: 4) Turn off the power supply and re

KMD-201AA KMD-201AWA - Hoshizaki

Create successful ePaper yourself

Delete template?

Save as template?