KMD-201AA KMD-201AWA - Hoshizaki

More documents

Recommendations

Info

7) Remove the front panel then remove the front insulation (the large insulation panel in frontof the evaporator) by lifting up the panel slightly and pulling it towards you.8) In bad or severe water conditions, clean the float switch as described below. Otherwise,continue to step 9.a. Loosen the two thumbscrews securing the pump motor bracket.b. Disconnect the discharge hose.c. Disconnect the pump motor connector and the float switch connector from the side of thecontrol box.d. Keep pushing up the snapping tab at the right side of the pump motor bracket.e. Pull out the water tank, cube guide, pump motor bracket, pump motor and float switchtogether.f. Remove the pump motor bracket securing the pump motor and the float switch. Removethe float switch from the pump motor bracket.51
g. Wipe down the float switch housing, shaft and float with cleaning solution. Rinse the partsthoroughly with clean water.h. Replace the float switch in its correct position.i. Replace the removed parts in the reverse order of which they were removed.9) Pour the cleaning solution into the water tank.10) Move the service switch to the "WASH" position.11) Replace the front insulation and the front panel in their correct positions.12) Turn on the power supply to start the washing process.13) Turn off the power supply after 30 minutes.14) Remove the front panel.15) Move the service switch to the "DRAIN" position.16) Replace the front panel in its correct position and turn on the power supply for 2 minutes.17) Turn off the power supply and remove the front panel.18) Move the control switch to the "ICE" position.19) Replace the front panel in its correct position.20) Turn on the power supply to fill the water tank with water.21) Turn off the power supply after 3 minutes.22) Remove the front panel.23) Move the control switch to the "SERVICE" position. Move the service switch to the"WASH" position.24) Replace the front panel in its correct position.25) Turn on the power supply to rinse off the cleaning solution.26) Turn off the power supply after 5 minutes.27) Remove the front panel.28) Move the service switch to the "DRAIN" position.29) Replace the front panel in its correct position and turn on the power supply for 2 minutes.30) Turn off the power supply.52
Page 1 and 2:
NO. F037-775ISSUED: JUN. 15, 2009RE
Page 3 and 4: [a] NO ICE PRODUCTION -------------
Page 6 and 7: II. GENERAL INFORMATION1. CONSTRUCT
Page 9 and 10: [e] NORMAL HARVEST CYCLELEDs 5, 6,
Page 11 and 12: 3. CONTROL BOARD* A HOSHIZAKI exclu
Page 13 and 14: [b] FEATURESa) Maximum Water Supply
Page 15 and 16: [c] CONTROLS AND ADJUSTMENTSa) Defa
Page 17 and 18: f) Freeze Timer (S1 dip switch 9 &
Page 19 and 20: 5. FLOAT SWITCH[a] EXPLANATION OF O
Page 21 and 22: 7. SWITCHESTwo different control sw
Page 23 and 24: 2. WIRING DIAGRAM20
Page 25 and 26: IV. SERVICE DIAGNOSIS1. 10-MINUTE D
Page 27 and 28: 2. DIAGNOSTIC CHARTS[a] NO ICE PROD
Page 29 and 30: 1. See "II. 3. [d] ControlBoard Che
Page 31 and 32: 1. See "II. 3. [d] ControlBoard Che
Page 33 and 34: V. REMOVAL AND REPLACEMENT1. SERVIC
Page 35 and 36: 2. BRAZINGNote: All brazing connect
Page 37 and 38: 5) Remove the Drier using brazing e
Page 39 and 40: 9) Evacuate the system, and charge
Page 41 and 42: 19) Turn on the power supply.9. ADJ
Page 43 and 44: 7) Remove the Hose Band connecting
Page 45 and 46: 10) Install the new water tank in t
Page 47 and 48: 8) Connect the bin control connecto
Page 49 and 50: 5) Refit the removed parts in the r
Page 51 and 52: 2) Install the new Run Capacitor in
Page 53: VI. CLEANING AND MAINTENANCE INSTRU
Page 57 and 58: [a] STAINLESS STEEL EXTERIORTo prev
Page 59: 4) Turn off the power supply and re
show all

KMD-201AA KMD-201AWA - Hoshizaki

Create successful ePaper yourself

Delete template?

Save as template?