TorqueStar DTT Opta Manual 7 - Crane Electronics

More documents

Recommendations

Info

OPERATOR’S MANUALSECTION 1To change the Torque LSL (Lower Specification Limit),key in the required figure (between the max. and min.displayed on screen).ROUNDSNOTE: A user must be logged in before any Round can beperformed.A round is a series of Jobs to be performed together as agroup. Each round must contain at least 2 Jobs.To access the Rounds modeFrom the Main menu - Other Modes screen, select theRounds icon. The Rounds screen will appear.To change the 2nd Parameter, choose between Angle,Pulse and None.To change the Angle Threshold, key in the required figure(between the max. and min. displayed on screen).To change the 2nd Param. USL (Upper SpecificationLimit), key in the required figure (between the max. andmin. displayed on screen).NOTE: The Second Param.USL and LSL can be displayedas either an angle or as a percentage of the USL. To change,select the desired option (radio button).To change the 2nd Param.Target, key in the required figure(between the max. and min. displayed on screen).To change the 2nd Param. LSL (Lower SpecificationLimit), key in the required figure (between the max. andmin. displayed on screen).Check boxes next to Job Comment, Comment andReference can be used to ensure the user is prompted toenter comments at the appropriate time.Icons used in the Jobs MenuAdd commentJob in progressJob completedAdd jobEdit jobDelete jobThe list shows up to 5 rounds per screen.Note: If the Show Description box is checked each pagewill show a single Round plus the description. Select thebox again to clear.Select the required round. The Perform Job screen will nowappear ready to accept a series of readings for the first Jobin the Round. This is the same screen as in the Jobs mode.As the user takes readings, the Opta will count down eachJob subgroup showing the name of the Job (see Jobs Modepage 21) until all of the Jobs in the Round are complete.The Opta screen will now return to the Rounds List.Select another round to perform or return to the Other ModesMenu.Select transducer24
OPERATOR’S MANUALSECTION 1Options AvailableAdd a new RoundEdit a RoundDelete a RoundNote: rounds completed or in progress cannot be deletedor edited.The following icons will appear next to the the Round numberto indicate the status of the Round.= Round in progress.= Round has been completed.Icons used in the Rounds MenuJob in progressSelect the Sampling field.Select the required sampling option from the list .Options are; In any order, Vertical, Horizontal, Vert.plus prompt, Horiz. plus prompt.To add a Job to the Round.Select add a new Job.Select the required job from the list.Continue this process until you have selected all the requiredjobs for the round.To save the round.Opta will prompt ‘Add round to list?’ENTER to accept or CANCEL to skip without saving.Icons used in the RoundsSetupJob completedReturn to previous screen.Return to previous screen.Previous pagePrevious pageNext pageNext pageEdit RoundView RoundAdd JobAdd RoundEdit JobEdit RoundMove job up listDelete RoundMove job down listDelete JobADDING NEW ROUNDS TO LISTTo add a new roundKey in the name for the round at the prompt and ENTER.Select the description field.Use the alpha-numeric keys to enter the round descriptionand ENTER.TRANSDUCER TEMPLATESThe TorqueStar Opta has 9 preset transducer templateswhich are editable by the user. This can be selected by theuser in Jobs mode if the transducer is non UTA and thereforenot recognised by the Opta.25
Page 1 and 2: TorqueStar Opta& DTT OptaOperator
Page 3 and 4: OPERATOR’S MANUALCONTENTSCE Marki
Page 5 and 6: OPERATOR’S MANUALSECTION 1OVERVIE
Page 7 and 8: OPERATOR’S MANUALSECTION 1SPECIFI
Page 9 and 10: OPERATOR’S MANUALSECTION 1OPTA CO
Page 11 and 12: OPERATOR’S MANUALSECTION 1SWITCHI
Page 13 and 14: OPERATOR’S MANUALSECTION 1USERSTh
Page 15 and 16: OPERATOR’S MANUALSECTION 1CONNECT
Page 17 and 18: OPERATOR’S MANUALSECTION 1From th
Page 19 and 20: OPERATOR’S MANUALSECTION 1Icons u
Page 21 and 22: OPERATOR’S MANUALSECTION 1VIEW ST
Page 23: OPERATOR’S MANUALSECTION 1Options
Page 27 and 28: OPERATOR’S MANUALSECTION 1USING A
Page 29 and 30: OPERATOR’S MANUALSECTION 1COMMUNI
Page 31 and 32: OPERATOR’S MANUALSECTION 1GLOSSAR
Page 33 and 34: OPERATOR’S MANUALSECTION 2OVERVIE
Page 35 and 36: OPERATOR’S MANUALSECTION 2CONTROL
Page 37 and 38: OPERATOR’S MANUALSECTION 2CONNECT
Page 39: Remove this page to use as a templa

TorqueStar DTT Opta Manual 7 - Crane Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?