Vapor Generation Accessory VGAâ77 Operation manual

More documents

Recommendations

Info

VGA–77'JHVSFÁÁPull the holder forward so that the cut-outs hook around the burner edge.'JHVSFÁÁLower the holder into position.Á'JHVSFÁ Mark 7 burner with holder in position2-12 Publication date: May 2004
VGA–77.BSLÁ7*ÁBOEÁ7*"ÁCVSOFSTÁIf you have a Mark VI or Mark VI-A burner, you will need a cellholder and suitable mounting brackets for these burners. (Refer tosection 6 for ordering information.)To install these mounting brackets on the burner, use the followingprocedure:1. Align the burner clamps at either end of the burner, with themounting peg pointing inward and the hole in the end of theplate aligned over the hole in the end of the burner.2. Use the screws provided to fix the burner clamps in position.✒ Note The clamps can be left permanently installed since they will notinterfere with normal flame analyses.'JHVSFÁ Mark VI burner with burner clamps installed✒ Note The Mark VI-A burner looks different to the Mark VI burner, howeverthe procedure for installing the clamps is the same..BSLÁ7ÁCVSOFSÁIf you have a Mark V burner (or earlier version), you will need a cellholder and burner mount for this burner. (Refer to section 6 forordering information.)Publication date: May 2004 2-13
Page 1 and 2: Vapor GenerationAccessory VGA-77Ope
Page 3 and 4: VGA-77Declaration of ConformityWe h
Page 5 and 6: VGA-77Contents ÁSafety practices a
Page 7 and 8: VGA-774.4 Basic methods 4-64.4.1 An
Page 10 and 11: VGA-77Electrical hazardsChemical ha
Page 13: VGA-771. Introduction1.1 About the
Page 18 and 19: REDACIDSAMPLEVGA-772.2 Installation
Page 20 and 21: VGA-772.2.2 Gas supply requirements
Page 22 and 23: VGA-774FMFDUJOHÁUIFÁWPMUBHFÁÁRe
Page 24 and 25: VGA-775. Fit the end of the tube fr
Page 26 and 27: VGA-773. Connect the inlet end of t
Page 30 and 31: VGA-77To install the burner clamp f
Page 32 and 33: VGA-77'JHVSFÁÁAdapter and Standar
Page 34 and 35: VGA-77*OTUBMMJOHÁBÁGMPXUISPVHIÁN
Page 36 and 37: REDACIDSAMPLEACIDSAMPLEVGA-77REDUCT
Page 38 and 39: VGA-772.2.13 Connection to the Auto
Page 40 and 41: VGA-77Use the integration mode with
Page 42 and 43: VGA-773.1.3 AA setup1. Remove the c
Page 45 and 46: VGA-774. Continue the previous step
Page 47 and 48: VGA-77❏❏Save your revised metho
Page 49 and 50: VGA-774. Analytical notes4.1 Backgr
Page 51 and 52: VGA-77For example, for Te and Se, a
Page 53 and 54: VGA-774.3 Laboratory procedures4.3.
Page 55 and 56: VGA-774.4.1 AntimonyPrepare samples
Page 57 and 58: VGA-77CautionRemember that AA mercu
Page 59 and 60: VGA-774.4.7 TinThe best results for
Page 61 and 62: VGA-775. Maintenance and spareparts
Page 63 and 64: VGA-77Under some circumstances, the
Page 65 and 66: VGA-77An alternative method of remo
Page 67 and 68: VGA-775.3 Spare parts✒ Note Use o
Page 69 and 70: VGA-776. Appendix-AA Performancelog

Vapor Generation Accessory VGAâ77 Operation manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Vapor Generation Accessory VGAâ77 Operation manual