You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
DRILL TEMPLATE SR 2003<br />
4<br />
5<br />
1. Compatibility<br />
The drill template SR 2003 is used for:<br />
SYMPRO-models.<br />
SR 100,<br />
SR 70,<br />
SR 45,<br />
CARVE PLATE 13 SLR (only Rental),<br />
CARVE PLATE 9 SLR (only Rental),<br />
The drill template can be used ski widths from<br />
59 mm to 82 mm. For wider or narrower skis you<br />
must use the Template Adapter Set<br />
(art. nr. 162 569).<br />
Note:: TYROLIA ski bindings with POWER BRAKE<br />
LD 78 can be used up to a ski width of 78 mm.<br />
For a ski widths from 79 mm to 90 mm use<br />
POWER BRAKE LD WIDE 90 (Art. Nr. 162 604).<br />
For a ski widths from 91 mm to 115 mm use<br />
POWER BRAKE LD FAT 115 (Art. Nr. 162 603).<br />
All adult bindings can be used for skis with a<br />
length of 140 cm and longer.<br />
2. Drill Bit<br />
If not otherwise specified by the ski manufacturer,<br />
for all SYMRENT adult models use a 4,1 Øx9,0mm<br />
drill bit for skis 140 cm and longer.<br />
For ski shorter than 140 cm use a 4,1 Ø x 7,0 mm<br />
drill bit. If mounted on TYROLIA Carve Plates<br />
replace the screws with longer ones (see screw<br />
chart page 34).<br />
3. Positioning the Drill Template<br />
Open the clamping jaws (4) by rotating the clamping<br />
handles (5) and then place template on the ski.<br />
Align the boot midsole indicator (3) for the appropriate<br />
binding model or Carve Plate with the midsole<br />
mounting mark on the ski.<br />
Be sure the template is evently seated against<br />
the ski’s top surface.<br />
▲<br />
CP-SLR 9 + SR100<br />
CP-SLR + SR70 (i-J)<br />
SR<br />
CENTERMARKS 2003<br />
CP-SLR + SR70 (q-R)<br />
SR100<br />
SR45 (j-w)<br />
3<br />
SR70 (q-R)<br />
SR45 (b-o)<br />
SR70 (i-J)<br />
CONTENTS<br />
Art.Nr.: 162635<br />
Release clamping handles (5) and attach the<br />
template firmly to the ski.<br />
Note: Some ski manufactures do not use the<br />
center of boot sole location method. Always follow<br />
the ski manufacturer’s instructions.<br />
4. Drilling the holes<br />
MOUNTING/ 25<br />
Drill through the appropriate bushings (see table)<br />
JUNIOR RACING PLATE (only Rental SR 70) Model Color of Indicator<br />
SR 100 Yellow<br />
SR 70 Blue (q-R)<br />
SR 70 White (i-J)<br />
SR 45 Red (b-o)<br />
SR 45 Green (j-w)<br />
CARVE PLATES Black<br />
If required by the ski manufacturer, tap the hole.<br />
After drilling place a drop of TYROLIA glue into the<br />
holes. It lubricates the screws and seals the holes<br />
(pict 26).<br />
pict 26<br />
▲<br />
CP-SLR 9 + SR100<br />
CP-SLR + SR70 (i-J)<br />
SR<br />
CENTERMARKS 2003<br />
CP-SLR + SR70 (q-R)<br />
SR100<br />
SR45 (j-w)<br />
SR70 (q-R)<br />
SR45 (b-o)<br />
SR70 (i-J)<br />
Art.Nr.: 162635