Technical Manual - Tyrolia

More documents

Recommendations

Info

32 / PLATES TYROLIA CARVE PLATES 2004/05 CARVE PLATE 13 SLR CARVE PLATE 9 SLR JUNIOR RACING PLATE ▲ CONTENTS ▲ Art.Nr.131046 Art.Nr.131047 Art.Nr.131048 Art.Nr.131049 Art.Nr.131074
MOUNTING PROCEDURE TYROLIA CARVE PLATES 1. General For proper mounting use drill template 92. The compatible binding-plate combinations can be found in the compatibility chart. All TYROLIA CARVE Plates can be used for ski’s 140 cm and longer. If mounted on ski’s shorter 140 cm the screws have to be replaced by shorter ones, see screw chart on page 34. For mounting SP 70 ABS, SL 70 CARVE ABS, SL 70 ABS, SL 70 or SR 70 on TYROLIA CARVE-Plates you have to replace the pre-mounted screws by screws with 8 mm penetration depth. Only with these screws can we guarantee the right pullout strength (see page 34). 2. Drill Bit If not otherwise specified by the ski manufacturer, use a 4,1 Ø x 9,0 mm drill bit. 3. Adjusting the Drill Template 92 Unlock the adjustment lever (1) by rotating it counterclockwise and push the template together as far as possible (23 cm). Fix the position by rotating the adjustment lever (1) clockwise until it stops (see template 92). 4. Positioning the Drill Template Open the jaws (4) of the template by rotating the handles (5) and place it on the ski with the boot midpoint indicator aligned with the mounting mark of the ski. For skiboot tip mounting align the corresponding sole length mark on the sticker (pict 45) with the boot tip mounting mark on the ski. Important! When mounting Rental bindings the boot midpoint indicator should be behind the mounting mark, in accordance with the enclosed table (page 35). For older drill templates stickers can be ordered from your local TYROLIA distributor: Drill Template 92 – art. nr. 159 383. 5. Drilling the holes Drill the holes using the appropriate TYROLIA drill bit. After drilling, drop some TYROLIA glue into the clean holes. This lubricates the screws and seals the hole. ▲ CONTENTS 5. Mounting ▲ MOUNTING/ 33 Place the front part of the plate over the holes and fasten the screws. Then place the back part over the holes and fasten the screws. For SPEED PLATE start with the back part. Determine the bootsole length with the TYROLIA Rental boot caliper and place the binding on the Carve Plate corresponding with the appropriate printed length markings. Mount the binding in accordance with the procedures in the <strong>Technical</strong> <strong>Manual</strong>. For skiboot tip oriented mounting only pict 45
Page 1 and 2: Technical Manual 2004/05 www.tyroli
Page 3 and 4: Skibindings 2004/2005 Active safety
Page 5 and 6: Faster adjustment to any boot sole
Page 7 and 8: Adapt your system Boot Center Adjus
Page 9 and 10: 03 04 DIAGONAL Toe Active protectio
Page 11 and 12: High-Light The new SL generation is
Page 13 and 14: ▲ CONTENTS ▲ RETAIL / 11 PARTS-
Page 15 and 16: ▲ CONTENTS ▲ RENTAL / 13 PARTS-
Page 17 and 18: DRILL TEMPLATE SELECTION Drill temp
Page 19 and 20: pict 1 6. Mounting For FREE FLEX PL
Page 21 and 22: Use a screwdriver to push the wedge
Page 23 and 24: pict 17 Adjusting the toe unit: The
Page 25 and 26: pict 21 5. Mounting Mounting the To
Page 27 and 28: DRILL TEMPLATE SR 2003 4 5 1. Compa
Page 29 and 30: TYROLIA brakes are compatible up to
Page 31 and 32: RAILFLEX System II Mounting of the
Page 33: 6. Forward pressure control Place t
Page 37 and 38: BINDING-PLATE COORDINATION LINE 200
Page 39 and 40: TYROLIA BRAKES LINE 2004/05 ▲ CON
Page 41 and 42: TYROLIA BRAKE MATRIX LINE 2004/05 8
Page 43 and 44: SR 70 The lightweight junior bindin
Page 45 and 46: Preparing and Checking Rental Syste
Page 47 and 48: 15. If many bindings fail, check th
Page 49 and 50: Rental / Demo of Partial Systems Ma
Page 51 and 52: pict 52 A1 5. Heel height and wear:
Page 53 and 54: Lubricate the new inserts with TYRO
Page 55 and 56: 2. Edge of the release cam under th
Page 57 and 58: Problem Possible Reason Solution Te
Page 59 and 60: SPAREPARTS, LINE 2004/05 Model SL 1
Page 61 and 62: SPAREPARTS, LINE 2004/05 S Y M P R
Page 63 and 64: SPAREPARTS, LINE 2003/04 HD 14 RAIL
Page 65 and 66: CLASSIFY YOURSELF DETERMINING YOUR
Page 67 and 68: If the intersection of the row and
Page 69 and 70: This section must be read, and thor
Page 71 and 72: device supplier to verify that thei
Page 73 and 74: Retailer Agreements and Indemnifica
Page 75 and 76: THE TYROLIA LIMITED WARRANTY TYROLI
Page 77 and 78: Racing (X) Bindings Certain binding
Page 79 and 80: Skiers Requesting Settings not Reco
Page 81 and 82: Shop Name Phone Address City State,
Page 83 and 84: CHIP TECHNOLOGY USED FOR RENTALS In
Page 85 and 86:
TYROLIA DEALER AREA - tyrolia.com O
Page 87:
HTM Sport- und Freizeitgeräte AG A
show all

Technical Manual - Tyrolia

Create successful ePaper yourself

Delete template?

Save as template?