GE Fanuc Automation - Platforma Internetowa ASTOR

More documents

Recommendations

Info

feedback of each temperature, output setting, and channel status is returned to the PLC in the %I and %AI data. The %Q data sent to the TCM is used for quick control of each of the eight output channels. In contrast, parameter data is sent to the TCM using groups of %AQ data to reduce the demand on the PLC I/O services. Full feedback of the TCM temperatures, outputs, and status is provided every PLC sweep for minimum system delays. To use the TCM, configure it as a Foreign module, with the default ID of 3, using the Logicmaster Configuration software. The module is assigned to a particular slot and rack like any other PLC module. The data transfer sizes are set to 64 %I, 28 %AI, 24 %Q, and 3 %AQ words of data communicated between the PLC and the TCM. GFK-1466 Chapter 1 Introduction 1-3 1
Chapter 2 Installing the Temperature Control Module This chapter describes the TCM and how to install it on the Series 90-30 PLC baseplate. The chapter is divided into the following sections. Section 1. Description of the TCM Section 2. Installing the TCM Section 1: Description of the TCM LED Indicators This section describes the LED indicators viewable on the faceplate and the TCM connections to field devices. The TCM indicator panel has 12 LEDs providing output and module status indications that are described below. (P) External Power. Green, normally ON. This light indicates that the external and internal power supplies are on. (R) Run. Green, normally ON. Lights steady when the TCM CPU is running properly. Alternately flashes with the red Fault LED if the internal CPU is unable to run to indicate total module failure. (F) Fault. Red, normally off. The fault light flashes upon module startup and extinguishes when the TCM CPU runs. The fault light flashes with the Run LED when a total module failure has occurred. (S) Short. Red, normally off. This LED lights when a short circuit is detected on one of the output channels. P R F S GFK-1466 2-1 1 5 R- S- S+ R 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8- INPUT +I/P TCM PWR +O/P P+ P- G 4 8 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8-
Page 1 and 2: Programmable Control Products Tempe
Page 3 and 4: Content of This Manual Related Publ
Page 5 and 6: Contents Example 1.................
Page 7 and 8: Contents Table 1-1. Firmware Compat
Page 9: 1 Auto Mode Diagnostic functions Th
Page 13: Section 2: Installing the TCM The T
Page 16 and 17: 3 Module Configuration Data Discret
Page 18 and 19: 3 Discrete Commands (%Q) been calcu
Page 20 and 21: 3 • The channels which will not b
Page 22 and 23: 3 Parameter Data (%AQ) A TCM Error
Page 24 and 25: 3 If any of the transferred paramet
Page 26 and 27: 4 PWM Output Period Auto-Tuning 1.
Page 28 and 29: 4 The following figure is an exampl
Page 30 and 31: 4 Closed-Loop Control Bias Lin.Cont
Page 32 and 33: 4 Power [%] 100% 0% -100% The follo
Page 34 and 35: 5 The series of pulses forces the p
Page 36 and 37: 5 • Period • Regulation Error L
Page 38 and 39: A 02-24-97 14:03 GE FANUC SERIES 90
Page 40 and 41: A %I0041 CH6_OE Channel #6 Output S
Page 42 and 43: A %R0099 CH7_SP CH7 Set Point %R010
Page 44 and 45: A |[ START OF SUBROUTINE LOGIC ] |
Page 47 and 48: Appendix B Specifications Tests and
Page 49 and 50: Appendix C Applications Heating and
Page 51: Implementing Low Voltage Bake-out A
Page 54: Index O Operating Temperature Setpo

GE Fanuc Automation - Platforma Internetowa ASTOR

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?