PA48 Mk2 Operator Manual - McConnel

More documents

Recommendations

Info

GENERAL INFORMATIONAlways read this manual before fitting or operating the machine – whenever any doubtexists contact your dealer or the McConnel Service Department for advice and assistance.Use only McConnel Genuine Service Parts on McConnel Equipment and MachinesDEFINITIONS – The following definitions apply throughout this manual:WARNINGAn operating procedure, technique etc., which –can result in personal injury or loss of life if not observed carefully.CAUTIONAn operating procedure, technique etc., which –can result in damage to either machine or equipment if not observed carefully.NOTEAn operating procedure, technique etc., which –is considered essential to emphasis.LEFT AND RIGHT HANDThis term is applicable to the machine when attached to the tractor and is viewedfrom the rear – this also applies to tractor references.MACHINE & DEALER INFORMATIONRecord the Serial Number of your machine on this page and always quote this number whenordering parts. Whenever information concerning the machine is requested remember also to statethe make and model of tractor to which the machine is fitted.Machine Serial Number:Machine Model details:Dealer Name:Dealer Address:Dealer Telephone No:Dealer Email Address:Installation Date:1
INTRODUCTION – Model SpecificationsPA48 Series (All Models)Linkage mounted.Right or left hand cutting.1.2M heavy duty flailhead (Hedge or Grass).Spring assisted gravity breakaway.Operator guard.180 litre hydraulic reservoir.PA48 SI ModelsSemi independent hydraulicsCable controls.Rotor engagement by tractor's PTO lever.54HP hydraulic system.PA48 TI ModelsTotally independent hydraulics powered by tandem PTO pump.Cable controls.Independent reversible rotor on/off valve.54HP hydraulic system.PA48E TI ModelsTotally independent hydraulics powered by tandem PTO pump.Electric controls - solenoid operated.Choice of control units - Switchbox, Monolever or ProportionalIndependent reversible rotor on/off valve.54HP hydraulic system.2
Page 1 and 2: Publication 597April 2009Part No. 4
Page 3 and 4: WARRANTY POLICYWARRANTY REGISTRATIO
Page 5 and 6: DECLARATION OF CONFORMITYConforming
Page 10 and 11: POWER ARM PRE-OPERATION InspectionP
Page 18 and 19: This machine has the potential to b
Page 20: ▲ Always disengage the machine, k
Page 23 and 24: VEHICLE / TRACTOR PREPARATIONWe rec
Page 25 and 26: DELIVERY & PRE-ATTACHMENT (Dealer R
Page 27 and 28: ATTACHMENT TO TRACTORAttachment of
Page 29 and 30: Raise the parking legs and secure i
Page 31 and 32: FITTING OPERATOR CONTROL UNITSFitme
Page 33 and 34: REMOVAL FROM TRACTORDANGER!READ CAR
Page 35 and 36: ARM OPERATIONRotor Control4Refer to
Page 37 and 38: CABLE ROTOR CONTROLOn cable rotor c
Page 39 and 40: ARM OPERATION25
Page 41 and 42: Switching the Rotor OnFor safety re
Page 51 and 52: ARM OPERATIONTele or Midcut/VFR Mod
Page 53 and 54: Switching Rotor DirectionWith the r
Page 55 and 56: ARMHEAD OPERATION - V4 JOYSTICK CON
Page 59 and 60: AUXILIARY FUNCTION CONTROLThis cont
Page 61: V4 CONTROL UNIT - LED Screen Displa
Page 64 and 65:
PRE-OPERATIONAL CHECKSCheck all bol
Page 66 and 67:
OPERATIONMaterial Thickness Cutting
Page 68 and 69:
Breakaway SystemThe machine is fitt
Page 70 and 71:
OVERHEAD POWER LINES (OHPLs)It cann
Page 72 and 73:
Preliminary PrecautionsAlways inspe
Page 74 and 75:
FLOATING HEAD ANGLE FACILITY (Optio
Page 76 and 77:
MAINTENANCEGeneral LubricationIMPOR
Page 78 and 79:
HYDRAULIC SYSTEMOil SupplyCheck the
Page 80 and 81:
CONTROL CABLESThe control cables op
Page 82 and 83:
TORQUE SETTINGS FOR FASTENERSThe ch
Page 84:
McConnel Limited, Temeside Works, L
show all

PA48 Mk2 Operator Manual - McConnel

Create successful ePaper yourself

Delete template?

Save as template?