PA48 Mk2 Operator Manual - McConnel

More documents

Recommendations

Info

HEAD FLOAT OPERATION - Angle Float / Lift Float (where features are applicable)Angle Float OFFLift Float OFFAngle Float OFFLift Float ONAngle Float ONLift Float ONROTOR OPERATION – Electric Rotor Control Models onlyNOTE: The following section relates to machines with Electric Rotor Control only – for Cable RotorControl models refer to the cable rotor control section.Selection of Rotor Cutting DirectionUphill CuttingDownhill Cutting30
Switching the Rotor OnFor safety reasons, to prevent accidental starting of the rotor, the ‘Rotor On’ switch cannotbe activated in a single operation or without first selecting the direction of cut – theprocedure for starting the rotor is as follows:Select the required cutting direction - the Rotor On/Off Switch (D) must then be switchedupwards and held in position for a minimum of 8 seconds before switching it into the fullydown ‘on’ position where it will remain until it is switched off. When the switch is moved tothe down position the red LED light above the switch will be lit to signify the rotor is on – ifthe LED does not light the switch was not held in its up position for long enough and therotor will not have started, repeat the process again holding the switch upwards for alonger period.Rotor StartSwitching the Rotor OffStopping the rotor is performed by switching either the Rotor Power Switch (D) or theRotor Direction Switch (E) to the central (off) position – the red LED light will go out tosignify the rotor has been switched off.Rotor StopCAUTION: When the rotor is switched off it will continue to ‘freewheel’ under its ownmomentum for up to 40 seconds before finally coming to a standstill – do not leave thetractor cab or attempt to approach the flailhead until the rotor has stopped turningcompletely.Alternative Rotor Stop31
Page 1 and 2: Publication 597April 2009Part No. 4
Page 3 and 4: WARRANTY POLICYWARRANTY REGISTRATIO
Page 5 and 6: DECLARATION OF CONFORMITYConforming
Page 10 and 11: POWER ARM PRE-OPERATION InspectionP
Page 16 and 17: GENERAL INFORMATIONAlways read this
Page 18 and 19: This machine has the potential to b
Page 20: ▲ Always disengage the machine, k
Page 23 and 24: VEHICLE / TRACTOR PREPARATIONWe rec
Page 25 and 26: DELIVERY & PRE-ATTACHMENT (Dealer R
Page 27 and 28: ATTACHMENT TO TRACTORAttachment of
Page 29 and 30: Raise the parking legs and secure i
Page 31 and 32: FITTING OPERATOR CONTROL UNITSFitme
Page 33 and 34: REMOVAL FROM TRACTORDANGER!READ CAR
Page 35 and 36: ARM OPERATIONRotor Control4Refer to
Page 37 and 38: CABLE ROTOR CONTROLOn cable rotor c
Page 39 and 40: ARM OPERATION25
Page 41 and 42: Switching the Rotor OnFor safety re
Page 43: ARM OPERATION29
Page 47 and 48: ARM OPERATION33
Page 49 and 50: Switching the Rotor OnFor safety re
Page 51 and 52: ARM OPERATIONTele or Midcut/VFR Mod
Page 53 and 54: Switching Rotor DirectionWith the r
Page 55 and 56: ARMHEAD OPERATION - V4 JOYSTICK CON
Page 59 and 60: AUXILIARY FUNCTION CONTROLThis cont
Page 61: V4 CONTROL UNIT - LED Screen Displa
Page 64 and 65: PRE-OPERATIONAL CHECKSCheck all bol
Page 66 and 67: OPERATIONMaterial Thickness Cutting
Page 68 and 69: Breakaway SystemThe machine is fitt
Page 70 and 71: OVERHEAD POWER LINES (OHPLs)It cann
Page 72 and 73: Preliminary PrecautionsAlways inspe
Page 74 and 75: FLOATING HEAD ANGLE FACILITY (Optio
Page 76 and 77: MAINTENANCEGeneral LubricationIMPOR
Page 78 and 79: HYDRAULIC SYSTEMOil SupplyCheck the
Page 80 and 81: CONTROL CABLESThe control cables op
Page 82 and 83: TORQUE SETTINGS FOR FASTENERSThe ch
Page 84: McConnel Limited, Temeside Works, L

PA48 Mk2 Operator Manual - McConnel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?