PA48 Mk2 Operator Manual - McConnel

More documents

Recommendations

Info

CLOSED CENTRE CONVERSION KIT – Semi-Independent Models onlyControl Valve Conversion Kit (Part No. 8130059)This consists of a relief valve-blanking plug, which should be installed in place of theexisting relief valve, and a pressure gallery blanking plug, which is installed in place of thestandard blanking plug at the valve outlet end next to the lift ram gland connection.NOTE: Take care when extracting the relief valve not to damage the copper sealingwasher, as it is to be re-used.When working in this mode the tractor's pressure control valve must not exceed 2500 P.S.I(170 Bar).9
DELIVERY & PRE-ATTACHMENT (Dealer Reference)DeliveryThe machine will be delivered in a partially dismantled condition secured with transportstraps and banding. Select a firm level site on which to place the machine before removingthe straps, banding and other loose items.Handling the MachineHandling of the machine should always be performed using suitable overhead liftingequipment with a minimum safe lifting capacity over and above the maximum weight of themachine. Always ensure the machine is balanced during the lifting procedure and that allbystanders are kept well clear of the raised machine.Post Delivery AssemblyIn allow for a compact shipping state the machine will be delivered with the tension linkdisconnected from the rocker and the stand legs retracted – these items will need to becorrectly installed before initial attachment to a tractor.The procedure is as follows:Stand LegsRaise the machine using suitableoverhead lifting equipment.Lower stand legs and secure inposition using pins and locking pins –the hole position selected should beat a height that places the gearboxstub axle approximately 75mm (3”)below the height of the tractor’s PTOshaft when the machine is at rest onthe ground. Note the hole positionused and ensure the equivalent oneis used on both sides of the machine.Tension Link AttachmentRequest assistance for this task- Operate ‘lift up’ on machinecontrols sufficient only for dipperarm to clear the ground.Pivot out the dipper arm until thetension link can be connectedand secure in position with pinand fixings supplied.10
Page 1 and 2: Publication 597April 2009Part No. 4
Page 3 and 4: WARRANTY POLICYWARRANTY REGISTRATIO
Page 5 and 6: DECLARATION OF CONFORMITYConforming
Page 10 and 11: POWER ARM PRE-OPERATION InspectionP
Page 16 and 17: GENERAL INFORMATIONAlways read this
Page 18 and 19: This machine has the potential to b
Page 20: ▲ Always disengage the machine, k
Page 23: VEHICLE / TRACTOR PREPARATIONWe rec
Page 27 and 28: ATTACHMENT TO TRACTORAttachment of
Page 29 and 30: Raise the parking legs and secure i
Page 31 and 32: FITTING OPERATOR CONTROL UNITSFitme
Page 33 and 34: REMOVAL FROM TRACTORDANGER!READ CAR
Page 35 and 36: ARM OPERATIONRotor Control4Refer to
Page 37 and 38: CABLE ROTOR CONTROLOn cable rotor c
Page 39 and 40: ARM OPERATION25
Page 41 and 42: Switching the Rotor OnFor safety re
Page 51 and 52: ARM OPERATIONTele or Midcut/VFR Mod
Page 53 and 54: Switching Rotor DirectionWith the r
Page 55 and 56: ARMHEAD OPERATION - V4 JOYSTICK CON
Page 59 and 60: AUXILIARY FUNCTION CONTROLThis cont
Page 61: V4 CONTROL UNIT - LED Screen Displa
Page 64 and 65: PRE-OPERATIONAL CHECKSCheck all bol
Page 66 and 67: OPERATIONMaterial Thickness Cutting
Page 68 and 69: Breakaway SystemThe machine is fitt
Page 70 and 71: OVERHEAD POWER LINES (OHPLs)It cann
Page 72 and 73: Preliminary PrecautionsAlways inspe
Page 74 and 75:
FLOATING HEAD ANGLE FACILITY (Optio
Page 76 and 77:
MAINTENANCEGeneral LubricationIMPOR
Page 78 and 79:
HYDRAULIC SYSTEMOil SupplyCheck the
Page 80 and 81:
CONTROL CABLESThe control cables op
Page 82 and 83:
TORQUE SETTINGS FOR FASTENERSThe ch
Page 84:
McConnel Limited, Temeside Works, L
show all

PA48 Mk2 Operator Manual - McConnel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?