Alspa CE80–20 FIP Bus Interface Unit User's Manual

More documents

Recommendations

Info

InstallationPage 2–16Alspa CE80–20 FIP Bus Interface Unit User’s ManualALS 52311 b–en
Chapter3OperationThis chapter explains how a Bus Interface Unit interacts with the modules in its I/O Station, how it stores data,and how it exchanges data with the system host.1. OPERATIONThe primary runtime operations of the Bus Interface Unit are to accept data from the FIP bus and pass this to thecorresponding output modules and to acquire updated input data for transmission onto the FIP bus.If a problem occurs (or is corrected) with any module or circuit, it is included in the status information regularlytransmitted by the Bus Interface Unit. Such module problems do not affect operation of the Bus Interface Unit orits communications on the network.ALS 52311 b–en Alspa CE80–20 FIP Bus Interface Unit User’s ManualPage 3–1
Page 1 and 2: AlspaIC670MDL643New In Stock!Cegele
Page 3 and 4: RevisionsPrefaceReader’scommentsC
Page 5 and 6: RevisionsPage 4Alspa CE80-20 FIP Bu
Page 7 and 8: Preface3. MANUAL NUMBERSIn some cas
Page 9 and 10: Reader’s commentsPage 8Alspa CE80
Page 11 and 12: Contents6. INSTALLING THE CABLES BE
Page 13 and 14: Chapter1IntroductionThis chapter in
Page 15 and 16: Introduction2. ALSPA CE80-20 MODULE
Page 17 and 18: Introduction3. LOCATIONS FOR ALSPA
Page 19 and 20: Introduction5. FIP BUS INTERFACE UN
Page 21 and 22: IntroductionNoteStart-up surge at f
Page 23 and 24: Introduction7. BUS INTERFACE UNIT F
Page 25 and 26: Introduction9. ALSPA C80-75 PLC: RE
Page 27 and 28: Chapter2InstallationThis chapter de
Page 29 and 30: Installation3. REMOVING THE BUS INT
Page 31 and 32: Installation5. INSTALLING THE BUS I
Page 33 and 34: Installation7. SETTING THE BIU DIP
Page 35 and 36: Installation9. SYSTEM WIRING GUIDEL
Page 37 and 38: Installation11. POWER WIRING TO THE
Page 39 and 40: Installation13. OBSERVING THE LEDSW
Page 41: Installation15. REMOVING THE BUS IN
Page 45 and 46: Operation3. IDLE MODEIdleReadyRunIn
Page 47 and 48: Operation5. RUN MODEIn Ready mode,
Page 49 and 50: Operation6.1. Discrete InputsThe Bu
Page 51 and 52: Operation6.2. Discrete OutputsThe B
Page 53 and 54: Operation6.3. Analog InputsThe Bus
Page 55 and 56: Operation6.4. Analog OutputsThe Bus
Page 57 and 58: Operation7. DIAGNOSTICSThe Bus Inte
Page 59 and 60: Operation7.2.3. Bus Interface Unit
Page 61 and 62: Chapter4Hand-Held Programmer Functi
Page 63 and 64: Hand-Held Programmer Functions1.2.
Page 65 and 66: Hand-Held Programmer Functions3. DI
Page 67 and 68: Hand-Held Programmer FunctionsFrom
Page 69 and 70: Hand-Held Programmer FunctionsThe f
Page 71 and 72: Hand-Held Programmer FunctionsS1 Ou
Page 73 and 74: Hand-Held Programmer Functions1. Fo
Page 81 and 82: Hand-Held Programmer Functions7. ER
Page 83 and 84: IndexALS 52311 b-en Alspa CE80-20 F
Page 85 and 86: IndexALS 52311 b-en Alspa CE80-20 F

Alspa CE80–20 FIP Bus Interface Unit User's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?