x series with advance micro - Sunbelt Transport Refrigeration

More documents

Recommendations

Info

CAUTIONOnly a refrigerant drum containing R404ashould be connected to units covered bythis manual in order to pressurize the system.Any other gas or vapor will contaminatethe system, which will require additionalpurging and evacuation of the highside (discharge) of the system.CAUTIONDo not vapor charge R404A systems. Onlyliquid charging through the receiver outlet(King) valve is acceptable.CAUTIONDo not over tighten or damage the SV2 orSV4 enclosing tube assembly. Torque to17-ft pounds (2.4 Mkg). Also make sure allparts are placed on the enclosing tube inproper sequence to avoid premature coilburnout.CAUTIONWhen adding oil to the compressor, extremecare must be taken to ensure the hoseis immersed in the oil at all times. Otherwiseair and moisture will be drawn into the compressor.CAUTIONWhen removing the compressor cylinderhead leave two cylinder head bolts loose<strong>with</strong> threads engaged in the crankcase untilcylinder head is completely loosened toprevent any residual crankcase pressure.62-106831--4
1.3 SAFETY DECALS62-03958-00 Heat WarningONLY USED ON UNITS WITH TWO-WAYCOMMUNICATION CAPABILITIES1--5 62-10683
Page 1 and 2: RTrailer & Rail RefrigerationEVAPOR
Page 3 and 4: 1How to use this manualPlease take
Page 5 and 6: TABLE OF CONTENTS (Continued)PARAGR
Page 15 and 16: LIST OF ILLUSTRATIONSFIGURE NUMBERP
Page 17 and 18: LIST OF TABLESTABLE NUMBERPageTable
Page 19 and 20: SECTION 1SAFETY PRECAUTIONS1.1 SAFE
Page 21: CAUTIONObserve proper polarity when
Page 25 and 26: OR1--7 62-10683
Page 27 and 28: 2.1 INTRODUCTIONWARNINGBeware of V-
Page 29 and 30: 9221232120645181719789 10 11 12 131
Page 31 and 32: 9232221123201945181716151467 891011
Page 33 and 34: 98765142 39CURBSIDE1.2.Evaporator f
Page 35 and 36: 9111098765432121. Control Module (M
Page 37 and 38: 92.3.3 Alternator/RegulatorElectric
Page 39 and 40: 9c. Loaded Operation (Figure 2-13)D
Page 41 and 42: 2.4.4 Evaporator Transducers and Se
Page 43 and 44: Figure 2-14 shows the control modul
Page 45 and 46: The Display and Keypad module is lo
Page 47 and 48: Table 2-3. FIELD EFFECT TRANSISTORS
Page 49 and 50: 2.6.2 Door and Remote SwitchesA uni
Page 51 and 52: 2.7 ENGINE DATA9Table 2-4. Engine D
Page 53 and 54: 92.12 SAFETY DEVICESSystem componen
Page 55 and 56: 2.14 REFRIGERANT CIRCUIT DURING COO
Page 57 and 58: SECTION 3OPERATION1PARAGRAPH NUMBER
Page 59 and 60: 3.2 MANUAL START - GLOW AND CRANK -
Page 61 and 62: 3.4 PRETRIPHEAT COOL DEFROST ALARM
Page 63 and 64: PRETRIP (Continued)Test 4 - Warm Up
Page 65 and 66: 3.5 CHANGING SET POINTHEAT COOL DEF
Page 67 and 68: 3.6.1 Start -Stop ParametersThe sel
Page 69 and 70: 3.8 SLEEP MODE ONHEATCOOL DEFROST A
Page 71 and 72: SLEEP MODE ON (Continued)No further
Page 73 and 74:
3.11 TRIP STARTHEAT COOL DEFROST AL
Page 75 and 76:
3.13 VIEW INACTIVE ALARMSHEAT COOL
Page 77 and 78:
3.14 UNIT DATAHEAT COOL DEFROST ALA
Page 79 and 80:
++**+*+*+*+*+*+Table 3-2. UNIT DATA
Page 81 and 82:
3.15 VIEW HOURMETERSHEAT COOL DEFRO
Page 83 and 84:
Table 3-3. Functional ParametersFUN
Page 85 and 86:
FUNCTIONALPARAMETERAIR FLOWAIR FLOW
Page 87 and 88:
FUNCTIONALPARAMETERSELECTIONSDESCRI
Page 89 and 90:
3.18 STOPPING UNIT1. To stop the un
Page 91 and 92:
DATA RECORDING (CONTINUED)Time Inte
Page 93 and 94:
a. Changing IntelliSetsHEAT COOL DE
Page 95 and 96:
3.20.4 AutoFresh Air ExchangeTo act
Page 97 and 98:
SECTION 4ENGINE1PARAGRAPH NUMBERPag
Page 99 and 100:
REPEAT “A”+ 10 SecondsGLOWTHIRD
Page 101 and 102:
4) The battery voltage is high enou
Page 103 and 104:
4.4 SPEED CONTROL OVERRIDESNOTEWith
Page 105 and 106:
SECTION 5TEMPERATURE CONTROL5.1 INT
Page 107 and 108:
5.6 UltraFresh 3 TEMPERATURE CONTRO
Page 109 and 110:
5.8 FreshProtectt SUPPLY AIR CONTRO
Page 111 and 112:
CSMV CONTROL+3.2_F (+1.8_C )+2.3_F
Page 113 and 114:
5.11.3 Normal Defrost OperationSV1
Page 115 and 116:
5.11.8 High Ambient Defrost Termina
Page 117 and 118:
Range Lock 1 & 2Range2issetfor0° t
Page 119 and 120:
Once the microprocessor detects tha
Page 121 and 122:
. ProductShield: High AirProductShi
Page 123 and 124:
5.18 MAXIMUM SUCTION OPERATING PRES
Page 125 and 126:
SECTION 6TECHNICIAN INTERFACE1PARAG
Page 127 and 128:
PCmodecanbeusedfor:• Changing set
Page 129 and 130:
CONFIGURATION SELECTIONS DESCRIPTIO
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
6.2.3 Service ModeCAUTIONService Mo
Page 141 and 142:
d. Auto Install ReeferManagerNOTEIf
Page 143 and 144:
6.5 INSTALLING NEW SOFTWARENOTEAll
Page 145 and 146:
6.5.3 Using ReeferManager to Instal
Page 147 and 148:
SETTING PM (PREVENTATIVE MAINTENANC
Page 149 and 150:
6.7.1 Microprocessor Replacementa.
Page 151 and 152:
NOTENone of the “Total” hourmet
Page 153 and 154:
6.7.9 Replacing Display Bezel Assem
Page 155 and 156:
SECTION 7MessageCenter7.1 MessageCe
Page 157 and 158:
MessageCOPY ERROR, REMOVE CARD XXCO
Page 159 and 160:
MessagePRETRIP FAIL IN TEST XXPRETR
Page 161 and 162:
SECTION 8ALARM TROUBLESHOOTING1PARA
Page 163 and 164:
8.2 NOTESNote 1 Active alarms will
Page 165 and 166:
AlarmNO.Steps ALARM / CAUSE CORRECT
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
SECTION 9SERVICEWARNINGBeware of V-
Page 277 and 278:
SYSTEMOPERATIONACTION/REFERENCESECT
Page 279 and 280:
IMMEDIATELY AFTER STARTINGENGINEFue
Page 281 and 282:
Table 9-2 CHECK AND RECORD THE FOLL
Page 283 and 284:
9.4 SURROUND REMOVALa. Place the St
Page 285 and 286:
9.6 PRIMING FUEL SYSTEM9.6.1 Mechan
Page 287 and 288:
9.8.2 Fuel Level SensorAn optional
Page 289 and 290:
1245b. Servicing the Speed Control
Page 291 and 292:
9.8.9 Engine Crankcase BreatherThe
Page 293 and 294:
Gearbox to Fan Shaft BeltTorque to
Page 295 and 296:
9.10 FANSHAFT ASSEMBLY - SEE FIGURE
Page 297 and 298:
9.10.4 Blower Wheel Installationa.
Page 299 and 300:
h. Open king valve and then check r
Page 301 and 302:
CAUTIONService mode MUST be used wh
Page 303 and 304:
h. Remove 10 bolts from the engine-
Page 305 and 306:
9.13.4 To Remove Oil From The Compr
Page 307 and 308:
9.16 CHECKING AND REPLACING FILTER-
Page 309 and 310:
9.18 COMPRESSOR DISCHARGE PRESSURET
Page 311 and 312:
9.19 COMPRESSOR SUCTION PRESSURETRA
Page 313 and 314:
NOTERebuild kit (P/N 14-00150-51) c
Page 315 and 316:
9.22 COMPRESSOR SUCTION MODULATIONV
Page 317 and 318:
f. Torque the 2 1/8” nut to 35 to
Page 319 and 320:
9.27 CONDENSER COIL CLEANINGRemove
Page 321 and 322:
9.29 UNIDRIVE TORQUE REQUIREMENTS(F
Page 323 and 324:
M8 x 1.25 x 20 mm lg(6 Required) 28
Page 325 and 326:
SECTION 10UNIT TROUBLESHOOTING1PARA
Page 327 and 328:
INDICATION / TROUBLEPOSSIBLE CAUSES
Page 329 and 330:
INDICATION/TROUBLEPOSSIBLE CAUSESAC
Page 331 and 332:
INDICATION/TROUBLE10.3.9Abnormal Pr
Page 333 and 334:
INDICATION/TROUBLEPOSSIBLE CAUSESAC
Page 335 and 336:
Using jumper wire,verify there is a
Page 337 and 338:
Replace ENSCU. Did youfind and corr
Page 339 and 340:
START HEREIs unit equippedwith Star
Page 341 and 342:
START HEREIs the unitequipped withS
Page 343 and 344:
START HEREIs the unit operating in
Page 345 and 346:
START HEREMake sure the Start/Run-O
Page 347 and 348:
START HEREAre you trying to load an
Page 349 and 350:
B. Compressor Inspection ProcedureN
Page 351 and 352:
START HEREGone through the system d
Page 354 and 355:
SECTION 11WIRING1PARAGRAPH NUMBERPa
Page 356 and 357:
Plugs used with Schematic 62 -04102
Page 358 and 359:
ADVANCE MICRO DISPLAY HARNESS CONNE
Page 360 and 361:
BASED ON DWG 62--10499 REV W
Page 362 and 363:
AAdvance Microprocessor Troubleshoo
Page 364 and 365:
LLanguage Selection, 3--31LIGHT BAR
Page 366:
North AmericaCarrier Transicold700
show all

x series with advance micro - Sunbelt Transport Refrigeration

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?