Razz plus - Hot Tubs, Hot Tub

More documents

Recommendations

Info

INSTALLATIONEquipment Set-Up1. Remove the plastic sheet covering the spa. Usecare; stepping into the spa with shoes will scratchthe acrylic surface.2. Remove any packing materials from the spa.3. Remove each filter cartridge from its plastic bag.4. Pull open each skimmer/filter door by the handlelocated in the middle of the door and remove theskimmer basket. Then insert the filter cartridge intothe filter housing and re-insert the strainer so that itfits in place over the filter cartridge and close theskimmer/filter door. See illustration on page 13.5. Clean the interior of the spa of any remaining constructiondebris. Remove stubborn stains, paint, ortar with turpentine, isopropyl alcohol or paint thinner.A mild liquid dishwashing detergent on a dampcloth is fine for cleaning off other dirt. Plaster can beremoved by scraping with a wooden edge; do notuse a metal scraper, wire brush, or other metal tools,as they will damage the spa's surface.6. Install the skirt panel which was not installed on thespa at the factory. To do this, secure with the screwsprovided in your spa accessory package and followinstructions provided with panels.7. On initial start-up, it is necessary to purge andsanitize the system. Carefully follow the proceduredescribed here to purge and sanitize your spa.• Remove the optional spa cover completely.• Close the drain valve located on the suction tee.• Fill the spa with water to its normal operating level,which is to the water level indicator mark on theskimmer/filter frame.• Turn on circuit breakers at the main electricalpanel.• Select JETS on the SYSTEM switch.• Add 1/4 cup sodium dichlor (a fast dissolvinggranular type of chlorine) to the water and let thewhirlpool run for 15-20 minutes only.• Turn off JETS.• Turn off circuit breakers.• Immediately open the drain valve and drain thespa completely.CAUTION: Leave the optional rigid cover offthe spa during this procedure. Do not use thespa during this procedure. Drain the spa immediatelyafterward.8. Close the drain valve and fill the spa with water toapprox. 9 inches below the spa rim, or to water lineindicator mark on the skimmer frame. (See illustrationon page13.)9. Turn on circuit breakers at the main service panel.10. Set the heater thermostat for the maximum temperature.11. Test the spa for proper operation. (Refer to OperatingInstructions.)12. Refer to Water Quality section of the OperatingInstructions. Test for water quality; then add treatmentchemicals to ensure proper levels.All Jacuzzi Whirlpool Bath spas are factory tested forproper operation and water tight connections prior toshipping. If leaks or other malfunctions are detected,immediately notify your Jacuzzi Whirlpool Bath dealer orAuthorized Service Agent, or call Jacuzzi WhirlpoolBath, (510) 938-7411 or, (510) 938-7070 for WarrantyService.SKIMMER/FILTERDOOR (2)AIR INDUCTIONCONTROL KNOBSFULLY ADJUSTABLEWHIRLPOOL JET (5)UNDERWATERLIGHTSUCTIONCOVER5
OPERATIONOPERATING INSTRUCTIONSNow that your <strong>Razz</strong>a Plus spa is in place, you are probably eager to take advantage of its unique designed-infeatures—especially the patented Jacuzzi Whirlpool Bath hydromassage performance. Besides being a beautifuladdition to your indoor decor or outdoor landscaping, your Jacuzzi ® whirlpool spa will provide you with the ultimatein spa pleasure.Basic Control Set-UpThe control set-up on your <strong>Razz</strong>a Plus spa is designed to give you fingertip control of the heater, air induction, lightand whirlpool, filter, and blower systems of your unit from inside or outside your spa. Follow the basic control setupdescribed below to familiarize yourself with the several functions of the control panels located on the top of the spa.CAUTIONDo not turn on power to the spa unless it is filled with water to the normal water level. (See water line indicatormark on skimmer frame.) When the power is on, the built-in timer may activate the system even though theSYSTEM is turned off at the control panel. If the spa’s motor/pump is actuated when there is not sufficientwater in the unit, the circulation pump and heater could be irreparably damaged. Not heeding this caution willnullify the warranty. In addition to damaging the unit, operating the spa with insufficient water could causea fire.• Using a garden hose, fill the spa with water to thewater line indicator mark on the skimmer frame.• At the house service panel, turn on the circuit breakeror switch that controls the electrical service to yourspa. (Make sure there is no other appliance on thatcircuit.)• Open the skirt door giving access to the SystemControl Module.• Your spa is provided with a ground fault circuit interrupter(GFCI). At initial start-up and at least once amonth thereafter, with power on, push the test buttonlocated on the System Control Module. The resetbutton should pop out. Push this button in to reset. Ifthe interrupter fails to operate in this manner, there isa ground current flowing or a device malfunctioning,indicating the possibility of electric shock. Turn offpower and do not use the spa until the source ofthe breakdown has been identified and corrected.6
Page 1 and 2: THE RAZZA PLUSTMPortable Whirlpool
Page 3 and 4: The Razza Plus Portable Whirlpool
Page 5 and 6: INSTALLATION INSTRUCTIONSInspection
Page 7: INSTALLATIONCAUTION: Do not apply e
Page 11 and 12: OPERATIONair blower and light. Refe
Page 13: OPERATIONNormal OperationWhirlpool
Page 16 and 17: MAINTENANCEWater Level/DrainThe wat
Page 18 and 19: MAINTENANCESpa LightColored filters
Page 20 and 21: TROUBLESHOOTING GUIDEPROBLEM6. Low
Page 22 and 23: ALEVELSPA SHELLWEIR BLADELeveling t

Razz plus - Hot Tubs, Hot Tub

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?