DCI Specs - Digital Cinema Initiatives

More documents

Recommendations

Info

Image ParametersNominal(Projected Image)Tolerances(ReviewRooms)Tolerances(Theatrical)Pixel Count 2048 x 1080 or 4096 x 2160 N/A N/ALuminanceUniformity, cornersand sidesCalibrated WhiteLuminance, centerCalibrated WhiteChromaticity, centerfrom code values[3794 3960 3890]Color Uniformity ofWhite Field, corners85%of center48 cd/m²(14 fL)80% to 90%of center±2.4 cd/m²(± 0.7 fL)70% to 90%of center±10.2 cd/m²(± 3.0 fL)x=.3140, y=.3510 ±.002 x, y ±.006 x, yMatches center±.008 x, yRelative tocenter±.010 x, yRelative tocenterSequential Contrast 2000:1 minimum 1500:1 minimum 1200:1 minimumIntra-frame Contrast 150:1 minimum 100:1 mininum 100:1 mininumGrayscale TrackingContouringNo visible color shadingContinuous, smooth ramp, withno visible stepsTransfer Function Gamma 2.6Color GamutColor AccuracyMinimum Color Gamut enclosedby white point, black point 11 andRed: 0.680 x, 0.320 y, 10.1 YGreen: 0.265 x, 0.690 y, 34.6 YBlue: 0.150 x, 0.060 y, 3.31 YColorimetricMatchNo visible colorshading(same)± 2% 10Per component(same)No visible colorshading(same)± 5% 11Per component(same)+/- 4 delta E 12 +/- 4 delta E 12Table 11: Reference Image Parameters and Tolerances8.3.4.8. Intra-frame (Checkerboard) ContrastWith the spot meter placed at the reference viewing position, measure the luminancelevels of each of the patches in the checkerboard test pattern. Intra-frame contrast iscomputed by summing the luminance of the white patches and dividing by the sum ofthe luminance of the black patches. Infra-frame contrast is reduced by many factorsincluding projection lens flare, port glass flare, ambient light spilling on the screen andback-reflections from the room itself. Note that this measurement is made with theprojector in situ, with the screening room or theater in full operating mode.8.3.4.9. Grayscale TrackingUsing the black-to-white gray step-scale test pattern described in Table 12: Black-to-White Gray Step-Scale Test Pattern Code Values, Luminance Values, and ChromaticityCoordinates, the entire step-scale should appear neutral without any visible color non-10 Least squares fit of slope of a log/log plot of measured luminance vs. input code value, using a range from peak whiteluminance down to 5% of peak white.11 The luminance of the black point is limited by the sequential contrast ratio of the projector plus the ambient light fallingon the screen.12 Delta E is color error, defined as the geometric sum of delta u’ and delta v’ (square root of sum of squares).DCI Digital Cinema System Specification v.1.2 Page 84
uniformity or non- monotonic luminance steps in the test pattern. The black-to-white graystep-scale test pattern shall be centered on the screen and occupy a rectangle sized20% of the screen height by 80% of the screen width. The background shall be definedby code values [1565 1633 1604], which define a luminance of 4.80 cd/m 2 andchromaticity coordinates x = 0.3140 y= 0.3510. Each step shall be 8% of the screenwidth and shall be defined by the code values in Table 12: Black-to-White Gray Step-Scale Test Pattern Code Values, Luminance Values, and Chromaticity CoordinatesInput Code ValuesOutput ChromaticityCoordinatesX’ Y’ Z’ x y Y1 379 396 389 0.3140 0.3510 0.122 759 792 778 0.3140 0.3510 0.733 1138 1188 1167 0.3140 0.3510 2.104 1518 1584 1556 0.3140 0.3510 4.435 1897 1980 1945 0.3140 0.3510 7.926 2276 2376 2334 0.3140 0.3510 12.727 2656 2772 2723 0.3140 0.3510 18.998 3035 3168 3112 0.3140 0.3510 26.879 3415 3564 3501 0.3140 0.3510 36.5010 3794 3960 3890 0.3140 0.3510 48.00StepNumberOutputLuminanceTable 12: Black-to-White Gray Step-Scale Test Pattern Code Values, LuminanceValues, and Chromaticity CoordinatesUsing the second black-to-dark gray step-scale test pattern described in Table 13:Black-to-Dark Gray Step-Scale Test Pattern Code Values, Luminance Values, andChromaticity Coordinates, the entire step-scale should appear neutral without any visiblecolor non-uniformity or non- monotonic luminance steps in the test pattern. The black-todarkgray step-scale test pattern shall be centered on the screen and occupy a rectanglesized 20% of the screen height by 80% of the screen width. The background shall bedefined by code values [122 128 125], which define a luminance of 0.0064 cd/m 2 andchromaticity coordinates x = 0.3140 y= 0.3510. Each step shall be 8% of the screenwidth and shall be defined by the code values in Table 13: Black-to-Dark Gray Step-Scale Test Pattern Code Values, Luminance Values, and Chromaticity CoordinatesDCI Digital Cinema System Specification v.1.2 Page 85
Page 1 and 2:
Digital Cinema Initiatives, LLCDigi
Page 3 and 4:
Table of Contents1. OVERVIEW 151.1.
Page 5 and 6:
5.2.2. Packaging Fundamental Requir
Page 8 and 9:
7.5.5.1. Introduction..............
Page 10 and 11:
9.4.2.5. Screen Management System (
Page 12 and 13:
Table of FiguresFigure 1: System Ov
Page 14 and 15:
THIS PAGE LEFT BLANK INTENTIONALLYD
Page 16 and 17:
equirements for encrypting the esse
Page 18 and 19:
• This document specifies a basel
Page 20 and 21:
DCI Digital Cinema System Specifica
Page 22 and 23:
2.1.1. Major System Concepts2.1.1.1
Page 24 and 25:
2.1.1.8. ReelsFeature films have be
Page 26 and 27:
Metadata within the DCDM provides a
Page 28 and 29:
3.2.1.6. Transfer FunctionThe CIE X
Page 30 and 31:
The information, as shown in Table
Page 32 and 33:
AES Pair#/Ch# Channel # Label / Nam
Page 34 and 35: 3.3.4. File Format3.3.4.1. GeneralT
Page 36 and 37: 3.4.3. Timed Text Concepts and Requ
Page 38 and 39: THIS PAGE LEFT BLANK INTENTIONALLYD
Page 40 and 41: • All decoders shall decode each
Page 44 and 45: 5.2.2.3. InteroperableThe Packaging
Page 46 and 47: Figure 6: Example Show PlaylistThe
Page 48 and 49: Length (Value Length), followed by
Page 50 and 51: which it was stopped or paused. It
Page 52 and 53: 5.3.4.2. Frame BoundariesThe Audio
Page 54 and 55: • Rating• Aspect Ratio• Image
Page 56 and 57: • Annotation Text parameter (opti
Page 60 and 61: 7.2.3.1. ReliabilityA key part of t
Page 62 and 63: • Country• Rating• Aspect Rat
Page 64 and 65: facility, while the system is in op
Page 66 and 67: Exhibitor and the Distributor, data
Page 68 and 69: 7.5.2.2. Ingest InterfacesExcept fo
Page 70 and 71: (channels) * hours * 60 min/hour *
Page 72 and 73: 7.5.4.2.4. UnpackagingAny packaged
Page 74 and 75: 7.5.6. Audio System7.5.6.1. Introdu
Page 76 and 77: made up of Theater System devices a
Page 78 and 79: DCI Digital Cinema System Specifica
Page 80 and 81: 8.2.2.3. Alternative ContentThe pro
Page 82 and 83: With the projector turned off or wi
Page 86 and 87: Input Code Values Output Chromatici
Page 88 and 89: 8.4. Projector Interfaces8.4.1. Int
Page 90 and 91: • Lens Shift Up / Down• Lamp Mo
Page 92 and 93: • Essence Encryption and Cryptogr
Page 94 and 95: content keys and Trusted Device Lis
Page 96 and 97: Figure 14: Digital Cinema Security
Page 98 and 99: Figure 15 presents the two fundamen
Page 100 and 101: DCI Digital Cinema System Specifica
Page 102 and 103: 9.4.2.3. Media Blocks (MBs)The term
Page 104 and 105: which TLS-based authentication alon
Page 106 and 107: working with the security infrastru
Page 108 and 109: Figure 18: Show Playback Overview9.
Page 110 and 111: a. Playout shall be fully supported
Page 112 and 113: 9.4.5. Intra-Theater Communications
Page 114 and 115: 4. Projector SPB designs shall not
Page 116 and 117: the event, and zero all Critical Se
Page 118 and 119: window) shall be UTC.Security Manag
Page 120 and 121: . The SM shall independently authen
Page 122 and 123: 6. No broadcast RRP commands shall
Page 124 and 125: Functions of the Security Manager (
Page 126 and 127: Note: DCI reserves the right, at so
Page 128 and 129: • Is required to survive camcorde
Page 130 and 131: • Log Data - Security event infor
Page 132 and 133: using the GetEventList and GetEvent
Page 134 and 135:
failure) per Section 9.6.1.3 Digita
Page 136 and 137:
• Secure Silicon -Sensitive data
Page 138 and 139:
secure silicon chip, input/output s
Page 140 and 141:
FIPS 140-2 level 3 devices provide
Page 142 and 143:
to the appropriate Section 9.4.5.2.
Page 144 and 145:
those under the control of the Secu
Page 146 and 147:
Security Managers (SMs) other than
Page 148 and 149:
The above RSA asymmetric protection
Page 150 and 151:
THIS PAGE LEFT BLANK INTENTIONALLYD
Page 152 and 153:
CPRL Acronym for Component Position
Page 154 and 155:
LTCMain TitlesMBMDMEMetadataMTBFMXF
Page 156:
TDLTimed TextTLMTLSTMSTrack FileUDP
show all

DCI Specs - Digital Cinema Initiatives

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?