Aqualab english manual

More documents

Recommendations

Info

Description of functionsThe functions of the dive plan mode are further described below.• Depth rank and no decompression limitThis mode displays a depth rank corresponding to the planned dive depth.The depth rank is indicated by the 14 rank level indicators shown below.This makes it possible to check the no decompression limit for the first dive or for aseries of dives.The no decompression limit indicator displays up to 200 minutes9 Meters 200 Minutes 30 Meters 16 Minutes12 Meters 104 Minutes 33 Meters 13 Minutes15 Meters 66 Minutes 36 Meters 11 Minutes18 Meters 47 Minutes 39 Meters 9 Minutes21 Meters 35 Minutes 42 Meters 8 Minutes24 Meters 25 Minutes 45 Meters 7 Minutes27 Meters 19 Minutes 48 Meters 7 Minutes30 Ft. 200 Minutes 98 Ft. 16 Minutes39 Ft. 104 Minutes 108 Ft. 13 Minutes49 Ft. 66 Minutes 118 Ft. 11 Minutes59 Ft. 47 Minutes 128 Ft. 9 Minutes69 Ft. 35 Minutes 138 Ft. 8 Minutes79 Ft. 25 Minutes 148 Ft. 7 Minutes89 Ft. 19 Minutes 157 Ft. 7 MinutesCAUTION !!!Be sure to set a dive plan that leaves a margin beyond the displayed nodecompression limit.• Residual nitrogen bar graphIndicates the current residual nitrogen level.• Oxygen Limit IndicatorIndicates the current level of oxygen toxicity exposure.• Surface timeIndicates the elapsed time since surfacing. The time counter starts when dive modeindicates a depth of less than 5 feet (1.5 meters). If the depth measurement becomes morethan 5 feet (1.5 meters) within the first ten minutes of Surface time, the previous divemode operations are continued.The Surface time can been measured for up to 48 hours, one minute after which it is turnedoff.11
• FO 2This indicates the current setting for the oxygen mix ratio (the percentage of oxygen in thenitrox mix). These settings are displayed as shown below.Note:SettingDisplay21% Air22% to 50% Percentage is displayedDefault “ - - “The default settings are 99% oxygen and 79% nitrogen. After NITROX divingusing a setting of 22% to 50%, the setting automatically switches to the defaultsetting after 10 minutes of Surface time or after 18 hours following completion of thesetting. This is convenient in cases where the diver forgets to set the mix for the nextdive. The setting does not switch automatically after air diving.CAUTION !!Be sure to set the oxygen percentage before each dive.• Maximum depth corresponding to FO 2The maximum allowable depth for a dive is determined based on the FO 2 setting.(For details, see the appendix.) If the depth rank exceeds the maximum depth,the no decompression limit indicator changes to " - - -".( - - - )12
Page 4 and 5: Aqualab Limited Warranty• Seac Di
Page 6 and 7: • Indication Mode.The arrow turne
Page 8 and 9: Description of functionsThe followi
Page 10 and 11: CAUTION !!!• Residual nitrogen ba
Page 14 and 15: Oxygen mix ratio setting modeThis m
Page 16 and 17: Operation of switches(beginning fro
Page 18 and 19: Oxygen toxicity exposure level warn
Page 20 and 21: Description of functionsThis functi
Page 24 and 25: • No decompression dive modeThe f
Page 26 and 27: • Ascent rate warningThis display
Page 28 and 29: Residual oxygen level warningCAUTIO
Page 30 and 31: Time setting modeThis mode is not d
Page 32 and 33: Change mode of measurement unitsThi
Page 34 and 35: Diving-related cautions• Be sure
Page 36 and 37: The computer will not switch to div

Aqualab english manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?