Aqualab english manual

More documents

Recommendations

Info

Description of functionsThe following functions are available during normal mode and surface mode.• DateThis shows the current date.• Current timeThis shows the current time (colon blinks).• Altitude rankThe computer automatically measures the current altitude and uses the rank symbolsdescribed below to indicate the altitude range.Measurements are retaken every 10 minutes.RANGEALTITUDE RANGE0 From 0,0 meters Sea Level To 800 meters1 From 800 meters To 1600 meters2 From 1600 meters To 2400 meters3 From 2400 meters To 6000 metersE Above 6000 meters “out of Range”RANGEALTITUDE RANGE0 From 0,0 Ft. Sea Level To 2624 Ft.1 From 2624 Ft. To 5248 Ft.2 From 5248 Ft. To 7872 Ft.3 From 7872 Ft. To 19680 Ft.E Above 6000 Ft. “out of Range”When the measured altitude is above 19,685 feet (6,000 meters), "E" is displayed andthe dive computer cannot be used. The computer is reset and becomes usable againwhen a lower altitude is measured. If the computer contains data such as residualnitrogen and oxygen data, the calculations and displays in effect when the computerdetects an altitude of more than 19,685 feet (6,000 meters) are retained while thecomputer is disabled and the retained values are restored when the measured altitudebecomes less than 19,685 feet (6,000 meters). The same displays and processing occurin cases where the computer is somehow unable to measure the altitude.Altitude measurements are performed in all modes except for dive mode and timesetting mode and transfer mode.The altitude rank symbol display is shown in all modes except for time settingmode, dive log mode, profile mode, and transfer mode. (However, the rankdisplay is shown while in dive mode.)• Surface timeThis indicates the amount of time since ascending to the surface: the time counterstarts when dive mode indicates a depth of less than 5 feet (1.5 meters). If the depthmeasurement becomes more than 5 feet (1.5 meters) within the first ten minutes ofsurface time, the previous dive mode operations are continued. The Surface time canbe measured for up to 48 hours, 1 minute after which it is automatically turned off.7
• Residual nitrogen bar graphThis bar graph contains 9 level indicators corresponding to the calculated amount ofresidual nitrogen in the body. A greater number of displayed indicators indicates ahigher level of residual nitrogen.• Desaturation timeThis indicates the amount of time until residual nitrogen is saturated. This display isshown until the displayed value reaches 0:00, and the display is shut off 1 minuteafterward.• Oxygen Limit Indicator (OLI)This bar graph contains 8 level indicators corresponding to the amount of oxygentoxicity exposure level in the body. A greater number of displayed indicators indicatesa higher level of oxygen toxicity exposure level.• Battery indicatorThe battery symbol indicates the battery's current voltage level. When symbol blinks,the AQUALAB will not enter dive mode, but can enter transfer mode. When batterysymbol stays ON, the dive computer cannot enter dive mode or transfer mode.Battery level measurements are made automatically in all modes except dive mode.8
Page 4 and 5: Aqualab Limited Warranty• Seac Di
Page 6 and 7: • Indication Mode.The arrow turne
Page 10 and 11: CAUTION !!!• Residual nitrogen ba
Page 12 and 13: Description of functionsThe functio
Page 14 and 15: Oxygen mix ratio setting modeThis m
Page 16 and 17: Operation of switches(beginning fro
Page 18 and 19: Oxygen toxicity exposure level warn
Page 20 and 21: Description of functionsThis functi
Page 24 and 25: • No decompression dive modeThe f
Page 26 and 27: • Ascent rate warningThis display
Page 28 and 29: Residual oxygen level warningCAUTIO
Page 30 and 31: Time setting modeThis mode is not d
Page 32 and 33: Change mode of measurement unitsThi
Page 34 and 35: Diving-related cautions• Be sure
Page 36 and 37: The computer will not switch to div

Aqualab english manual

Create successful ePaper yourself

Delete template?

Save as template?