EMC Avamar 6.0 for Exchange Guide - EMC Community Network

More documents

Recommendations

Info

Configuring the Avamar Cluster ClientINSTALLATIONFIELD/OPTIONDo not registerclient now optionAdministrator serverhost name or IPaddressDESCRIPTIONIf selected, client associated with thiscluster group will not be registered with theAvamar server. This client will have to bemanually registered and activated beforeyou can back up any data.Administrator server network hostname asdefined in DNS.REGISTRATIONAdministrator serverlisten data portBackup domain forthis clientThe default data port for Avamar clientservercommunication is 28001.Unless you are using a different data portat your site, you should leave this set to28001.Consult your Avamar system administratorfor the specific data port you should usewhen registering this client.Avamar domain where you want this clientto reside.The default domain is “clients.” However,your Avamar system administrator mighthave defined other domains and subdomains.Consult your Avamar system administratorfor the specific domain you should usewhen registering this client.IMPORTANT: If typing a sub-domain(for example, clients/MyClients), do notinclude a slash (/) as the first character.Including a slash as the first character willcause an error and prevent you fromregistering this client.Override automaticbackup client namewith this nameIf you do not want the Avamar client nameto be the same as the cluster group name,type another Avamar client name in thisfield.PLUG-INSInstall following pluginsDisplays all of the plug-ins currentlyinstalled that will work on clusters.Generally you will not need to change thedefaults.If you don’t want Avamar to use aparticular plug-in, select the item and thenclick Remove.If you want to reload the complete list ofplug-ins that were displayed when youopened this window, click Set All.EMC AVAMAR 6.0 FOR EXCHANGE GUIDE 39
Configuring the Avamar Cluster ClientINSTALLATIONFIELD/OPTIONDESCRIPTIONCLUSTER NODESPerform installation onfollowing nodesDisplays a list from Windows clusterservices of all of the nodes that are part ofthe cluster. Generally you will not need tochange the defaults.If there is a node on the cluster that youdon’t want the cluster backup agent serviceinstalled on, select the item and then clickRemove.If you want to reload the complete list ofnodes that are part of this cluster, click SetAll.4. Click Configure.You may be prompted for credentials to run the Avamar service in thefollowing circumstances:• When the UNC path is specified for var folder. The following messagewill be displayed: Please enter credentials to enable Avamarservice to access network shared var folder.• When the Exchange message plug-in is installed. The followingmessage will be displayed: Please enter credentials to enablemessage level backups and restores.When installation is complete, a message box will confirm the configurationof the client is complete, and will list the plug-ins that were configured.After you click OK, the setup dialog box is displayed, and the Install buttonwill be greyed out.IMPORTANT: If the Var folder is on a network share, youmust start the backup cluster agent from an account thathas full access permissions to the folder where Avamar logfiles are written.EMC AVAMAR 6.0 FOR EXCHANGE GUIDE 40
Page 1 and 2: EMC ® AVAMAR ® 6.0FOR EXCHANGEGUI
Page 3 and 4: TABLE OF CONTENTSPreface . . . . .
Page 5 and 6: PREFACEScope and intended audienceS
Page 7 and 8: Safety admonitions and noticesPREFA
Page 9 and 10: INTRODUCTIONThe Avamar Exchange Cli
Page 11 and 12: Important terms and conceptsINTRODU
Page 13 and 14: System requirementsINTRODUCTIONSupp
Page 15 and 16: Capabilities and limitationsINTRODU
Page 18 and 19: Capabilities and limitationsINTRODU
Page 20 and 21: INSTALLATIONThis chapter describes
Page 22 and 23: Quick reference installation road m
Page 24 and 25: 10. Click Finish to complete the in
Page 26 and 27: Configuring Exchange Server 2007 fo
Page 38 and 39: Configuring the Avamar Cluster Clie
Page 42 and 43: Uninstalling and upgrading Avamar E
Page 44 and 45: Uninstalling an older version of Cl
Page 46 and 47: BACKUPThis chapter describes how to
Page 48 and 49: Seeding the Avamar server for first
Page 50 and 51: Backing up an entire Exchange Datab
Page 52 and 53: Backing up an entire Exchange Datab
Page 54 and 55: Backing up one or more message fold
Page 66 and 67: Recovering an entire Exchange datab
Page 68 and 69: Recovering an entire Exchange datab
Page 70 and 71: Restoring to a RSG with the Windows
Page 72 and 73: Restoring to a RSG with the Windows
Page 74 and 75: Restoring to a RSG on an alternate
Page 76 and 77: Restoring to a RSG on an alternate
Page 78 and 79: Recovering to a Storage Group on a
Page 80 and 81: APPENDIX A — PLUG-IN OPTIONSImpor
Page 82 and 83: Windows Exchange database plug-in o
Page 88 and 89: APPENDIX B — MANUALLY CREATING TH
Page 90 and 91:
Manually creating the AvamarBackupU
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
INDEXclustercreate AvamarBackupUser
Page 104:
INDEXWwarningnot provided for hidde
show all

EMC Avamar 6.0 for Exchange Guide - EMC Community Network

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?