RBK 825 Recumbent Bike - Experienceâ¢ Series - Precor

More documents

Recommendations

Info

16 Assembling and Maintaining RBK 800-Series Recumbent Exercise BikesAttaching the Seat Back and Bottle HolderWhile the equipment is in use, the seat back flexes to supportusers of different shapes and sizes. Underneath the seat back,the bottle holder accommodates both left-handed andright-handed users.To attach the seat back:1. Insert the lower front edge of the seat back assemblyunder the seat.2. Swing the seat back assembly into place so that its fourscrew holes line up with the holes on the seat carriagebracket, as shown in the following illustration.Figure 2: Moving the seat back assembly into position3. Place four ⁵₁₆-inch washers onto four ⁵₁₆-inch x ³₄-inchsockethead screws.4. Insert the screws through the holes in the seat backassembly and thread them into the seat carriage bracket.5. Adjust the position of the seat back, then tighten thescrews completely using a ¹₄-inch hex wrench.
Assembling the Exercise Bike 17To attach the bottle holder:1. Position the bottle holder so that it wraps around the seatback assembly and rests on the tab on the back of theassembly. The front edges of the bottle holder should reston the handlebars and the two snap-in tabs should line upwith the small rectangular holes on the seat backassembly.2. Press the bottle holder forward until it locks into place.Installing the Upright Support and CablesDANGERDo not attempt to connect electrical power until allassembly procedures are complete and the consoleis properly installed.Before you begin this procedure, retrieve the cables for theconsole that you plan to install on this exercise bike. Thecables are packed with the console.Note: You will need the help of another person whileperforming the procedure.To prepare the bike for installation of the upright support:1. Retrieve the cables from the box in which the console wasshipped.2. Using a #2 Phillips screwdriver, remove the two #10 x1-inch self-tapping screws holding the top cover in place,then lift it off. Lift the cover from its front edge first, thendisengage its plastic tabs from the recesses on the rearcover into which they fit.Figure 3: Top cover removal
Page 1:
Operating and Maintainingthe P20 Co
Page 5 and 6:
Important Safety InstructionsThis a
Page 7 and 8:
Important Safety Instructions 5•
Page 9 and 10:
Important Safety Instructions 7In a
Page 11 and 12:
Important Safety Instructions 9Elec
Page 13 and 14:
Table of ContentsImportant Safety I
Page 15 and 16: Chapter 1Getting StartedThe P20 con
Page 17 and 18: Chapter 2Setting Up the ConsoleUse
Page 19 and 20: Setting Up the Console 17Number Par
Page 21 and 22: Setting Up the Console 19Event LogT
Page 23 and 24: Setting Up the Console 21Lower Soft
Page 25 and 26: Setting Up the Console 23Max Resist
Page 27 and 28: Setting Up the Console 25Equipment
Page 29 and 30: Chapter 3Introducing Users to the P
Page 31 and 32: Introducing Users to the P20 Consol
Page 33 and 34: Introducing Users to the P20 Consol
Page 35 and 36: Chapter 4Starting a WorkoutCAUTION:
Page 37 and 38: Starting a Workout 35To enter perso
Page 39 and 40: Starting a Workout 37Understanding
Page 41 and 42: Chapter 5ProgramsPreset workouts ar
Page 43 and 44: Programs 41Basic Heart Rate Control
Page 45 and 46: Chapter 6MaintenanceTo keep the equ
Page 48 and 49: Precor Incorporated20031 142nd Aven
Page 52 and 53: Edition InformationASSEMBLING AND M
Page 54 and 55: 4 Assembling and Maintaining RBK 80
Page 98: 48 Assembling and Maintaining RBK 8
show all

RBK 825 Recumbent Bike - Experienceâ¢ Series - Precor

Create successful ePaper yourself

Delete template?

Save as template?

RBK 825 Recumbent Bike - Experienceâ¢ Series - Precor