configuring ports - Lantech Communications Global Inc

More documents

Recommendations

Info

CONFIGURING MANAGEMENT POLICYThrough the management security configuration, the manager can do the strictsetup to control the switch and limit the user to access this switch.WEB INTERFACETo configure Management Policy in the web interface:1. Click SYSTEM, Management Policy.2. Add a Management policy rule.3. Click Add.4. If you click delete then switch will delete a exist managementpolicy.NOTE: The following rules are offered for the manager to manage the switch:Rule 1) : When no lists exists, then it will accept all connections.Accept-----------------------------------------------------------------------Rule 2) : When only “accept lists” exist, then it will deny all connections, excludingthe connection inside of the accepting range.Rule 3) : When only “deny lists” exist, then it will accept all connections, excludingthe connection inside of the denying range.Rule 4) : When both “accept and deny” lists exist, then it will deny all connections,excluding the connection inside of the accepting range.Rule 5) : When both “accept and deny” lists exist, then it will deny all connections,excluding the connection inside of the accepting range and NOT inside of thedenying range at the same time.
Figure 4-6: Management Policy ConfigurationPARAMETERSThese parameters are displayed on the Management Policy configuration page:• Add. – To create a new management policy. Specify new entry ofManagement Security Configuration can be created after theparameters as mentioned above had been setup• Delete – To delete a exist Management policy from themanagement policy List.• Name - A name is composed of any letter (A-Z, a-z) and digit (0-9)with maximal 8 characters.• VID - The switch sup<strong>ports</strong> two kinds of options for managed validVLAN VID, including ―Any‖ and ―Custom‖. Default is ―Any‖. Whenyou choose ―Custom‖, you can fill in VID number. The valid VIDrange is 1~4094.
Page 1 and 2: LantechLGS-2816C-RPS16 100/1000M SF
Page 3 and 4: ABOUT THIS GUIDEPURPOSEThis guide g
Page 5: CONTENTS
Page 8 and 9: Table 1-2: Key Features (Continued)
Page 10 and 11: REDUDANTPOWER SUPPLYPORT CONFIGURAT
Page 12 and 13: QUALITY OF SERVICE Differentiated S
Page 14 and 15: Table: System Defaults (Continued)F
Page 16 and 17: 2 INITIAL SWITCH CONFIGURATIONThis
Page 18 and 19: ■■■■Set the data format to
Page 20 and 21: NOTE: An IPv4 address for this swit
Page 22 and 23: COMMUNITY STRINGS (FOR SNMP VERSION
Page 24 and 25: CHAPTER 2 | Initial Switch Configur
Page 26 and 27: 33 USING THE WEB INTERFACEThis swit
Page 28 and 29: PANEL DISPLAY The web agent display
Page 30 and 31: WizardConfigures ACL via Wizard set
Page 32 and 33: Export/ ImportAllows user can back
Page 34 and 35: CHAPTER 4 | Configuring the SwitchS
Page 36 and 37: CHAPTER 4 | Configuring the SwitchS
Page 38 and 39: CONFIGURING TIMEThe switch provides
Page 40 and 41: Default: 1CHAPTER 4 | Configuring t
Page 42 and 43: PARAMETERSThese parameters are disp
Page 46 and 47: • IP Range - The switch supports
Page 48 and 49: CONFIGURING SYSTEM LOGThe System Lo
Page 50 and 51: PARAMETERSThese parameters are disp
Page 52 and 53: ■■■■■■CHAPTER 4 | Confi
Page 54 and 55: CHAPTER 4 | Configuring the SwitchC
Page 56 and 57: the manufacturer.CHAPTER 4 | Config
Page 58 and 59: CONFIGURING SIMPLE COUNTERThe funct
Page 60 and 61: CONFIGURING DETAIL COUNTERThe funct
Page 62 and 63: CRC.CHAPTER 4 | Configuring the Swi
Page 64 and 65: IEEE 802.1Q VLANSThe switch support
Page 66 and 67: Segment Forwarding Port Mapping1 Po
Page 68: • VLAN ID - VLAN identifier. Each
Page 71 and 72: CHAPTER 4 | Configuring the SwitchC
Page 73 and 74: CONFIGURING PORT ISOLATIONPort Isol
Page 75 and 76: CONFIGURING MACMAC Table Configurat
Page 77 and 78: CONFIGURING STATIC FILTERStatic Fil
Page 79 and 80: CONFIGURING MAC ALIASMAC Alias func
Page 81 and 82: CONFIGURING GVRPGVRP is an applicat
Page 83 and 84: CONFIGURING COUNTERAll GVRP counter
Page 85 and 86: CONFIGURING GROUPThe Function will
Page 87 and 88: • Default Class - User can set up
Page 89 and 90: Ethertype(Hexadecimal)0x08000x08010
Page 91 and 92: CONFIGURING RATE LIMITERSEach port
Page 93 and 94: CONFIGURING STORM CONTROLYou can co
Page 95 and 96:
CONFIGURING QoS WIZARDYou can use t
Page 97 and 98:
Figure 4-36: Set up Port Policy Fin
Page 99 and 100:
PARAMETERSThese parameters are disp
Page 101 and 102:
SNMP SYSTEMCONFIGRATIONThis functio
Page 103 and 104:
SNMPv3 USERSCONFIGRATIONThe functio
Page 105 and 106:
SNMPv3 GROUPSCONFIGRATIONThe functi
Page 107 and 108:
SNMPv3 VIEWSCONFIGRATIONThe functio
Page 109 and 110:
Auth, Priv: Authentication and priv
Page 111 and 112:
• Version - Scroll SNMP Version t
Page 113 and 114:
3. Repeat the preceding step for ea
Page 115 and 116:
ACL RATE LIMITERsCONFIGRATIONThe AC
Page 117 and 118:
Figure 4- 50: Access Control List C
Page 119 and 120:
‣ EtherType Filter - This option
Page 121 and 122:
TCP Parameters‣ Source Port Filte
Page 123 and 124:
ACLS WIZARDCONFIGRATIONThe wizard f
Page 125:
Figure 4- 54: Set up ACL Wizard Typ
Page 128 and 129:
Page 130 and 131:
only pass the packets when the auth
Page 132 and 133:
9. When the authenticator PAE recei
Page 134 and 135:
Two characters. Default is Radius.A
Page 136 and 137:
• Mode - Scroll the Range: Disabl
Page 138 and 139:
802.1X Status The function is using
Page 140 and 141:
CONFIGURING TACACS+TACACS+ (Termina
Page 142 and 143:
TACACS+AUTHORIZATIONCONFIGURATIONTh
Page 144 and 145:
CONFIGURING TRUNKThe Port Trunking
Page 146 and 147:
CHAPTER 4 | Configuring the Switch
Page 148 and 149:
TRUNKAGGREGATORVIEWThe function pro
Page 150 and 151:
TRUNKAGGREGATIONHASH MODECONFIGURAT
Page 152 and 153:
CONFIGURING SPANNING TREE PROTOCOLT
Page 154 and 155:
designated port of the root bridge.
Page 156 and 157:
SPANNINGTREE PROTOCOLCONFIGURATIONT
Page 158 and 159:
SPANNING TREE PORTCONFIGURATIONThe
Page 160 and 161:
CHAPTER 4 | Configuring the SwitchU
Page 162 and 163:
-180 -CHAPTER 4 | Configuring the S
Page 164 and 165:
CONFIGURING MULTIPLE SPANNING TREE
Page 166 and 167:
MSTPINSTANCE VIEWCONFIGURATIONThe F
Page 168 and 169:
CHAPTER 4 | Configuring the SwitchC
Page 170 and 171:
Figure 4-81: Display the MSTP Insta
Page 172 and 173:
specification Possible values are
Page 174 and 175:
CHAPTER 8 | Commands of CLIAlarm Co
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
MVRCONFIGRATIONCHAPTER 8 | Commands
Page 182 and 183:
PARAMETERSCHAPTER 8 | Commands of C
Page 184 and 185:
• Previous Page - Display previou
Page 186 and 187:
NOTE: The system default Alarm even
Page 188 and 189:
CONFIGURING DHCP SNOOPINGThe addres
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
DISPLAYINGLLDP NEIGHBORINFORMATIONT
Page 196 and 197:
-346 -CHAPTER 8 | Commands of CLIAl
Page 198 and 199:
CONFIGURING SAVE / RESTOREThe switc
Page 200 and 201:
SAVE STARTSave the current configur
Page 202 and 203:
CONFIGURING EXPORT / IMPORTWith thi
Page 204 and 205:
DIAGNOSTICSThree functions, includi
Page 206 and 207:
MAINTENANCEThis chapter will introd
Page 208 and 209:
LOGOUTYou can manually logout by pe
Page 210 and 211:
EXAMPLELGS-2816C-RPS(802.1X)# set m
Page 212 and 213:
LGS-2816C-RPS(802.1X)# set quietPer
Page 214 and 215:
LGS-2816C-RPS(802.1X)# set reAuthPe
Page 216 and 217:
DEFAULT SETTINGValue - 30EXAMPLELGS
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
SYNTAXadd operator name - New accou
Page 224 and 225:
7ACL Commands of CLITable 7-1: ACL
Page 226 and 227:
16 1 permit Disabled Disabled 017 1
Page 228 and 229:
moveThis command move ACE configura
Page 230 and 231:
vid - The VLAN to filter for this r
Page 232 and 233:
DEFAULT SETTINGSee defaults in Synt
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
ASOFTWARE SPECIFICATIONSSOFTWARE FE
Page 240 and 241:
APPENDIX A | Software Specification
Page 242 and 243:
IP Multicasting related MIBsMAU MIB
Page 244 and 245:
USING SYSTEM LOGSIf a fault does oc
Page 246 and 247:
DNS Domain Name Service. A system u
Page 248:
that it takes a message and convert
show all

configuring ports - Lantech Communications Global Inc

Create successful ePaper yourself

Delete template?

Save as template?