MU-78-10 BEAT-HF - Acuster Bahisa

More documents

Recommendations

Info

USER MANUALBEAT-HFnnnnhh:mmCouplerAG d6340.0 V 75s 2.25ÙConfirmWhere the following information appears:Coupler: Type of fitting connectedAG d63: Make and diameter of fitting40.0V 75s 2.25Ù: Electrofusion parametersIf the barcode or reading were erroneous.nnnnFusion datavvv V ff Hz tt°CWrong datahh:mmIf a barcode has been entered incorrectly, the unit willemit two acoustic signals and a Wrong data willappear on the screen.Read the barcode again.Once the data have been successfully read, the unit will remain await for confirmation toproceed. Press to go back to the previous screen or to continue.dd/mm/yyScrapped & Cleanhh:mmConfirmation is requested of whether the scraping andde-greasing of the pipes has been done.ConfirmPress to go back to the initial screen of Fusion data or to continue.dd/mm/yyhh:mmClamp ConfirmConfirmation is requested of whether a clamp mountedon the pipes was used.The cursor remains positioned on by default.Press the arrow to move it to , depending onthe situation.Press to go back to the previous screen or to continue.nnnnhh:mm40.0 V 0075s 2.25Ù0072sPress On the top line, the fusion parameters read from thefitting’s barcode will be shown.0072s: Time of electrofusion (*)(*) The time of the electrofusion can vary in relation to the nominal value due to thecorrection of the room temperature, that being included in the barcode by the manufacturerof the fitting or being beyond the temperatures not rectified.Press to go back to the initial Fusion data screen or to continue.30Edition: April 2012- MODE OF USE Revision: No. 2
USER MANUALBEAT-HF3.4.4 Input of electrofusion data in the unit by means of the keyboard:If the input of data related to the Operator, Job, Additional data, Traceability is disabledor, if enabled, once validated, the following screen will appear:nnnnFusion datavvv V ff Hz tt°CRead barcodehh:mmPress either the or arrow to select the Manualfusion or Edit barcode screen, depending on thesituation (see WARNING).Select the Manual fusion option when the electrofusion parameters (voltage and time)need to be introduced manually, without the traceability of the manufacturer of the fitting,and select Edit barcode when the fitting manufacturer’s data needs to be kept and anoptic pen or scanner is not available.WARNING !The Manual fusion option could be disabled. If it is the case, the unit willnot be able to perform manual electrofusions. Selecting the Manual fusion option: only if enabled.Press to validate. The display will show the following screen:nnnnVoltagehh:mm40.0VConfirmThe display will show the voltage of the electrofusionof 40.0V by default or that used in the previouselectrofusion cycle (if the unit has not been turned off).The electrofusion voltage must be between 8 and48 V.If the fitting’s electrofusion voltage is not 40.0V, change it by pressing the arrow toincrease the voltage and the arrow to reduce it. The values displayed on the screen areshown in steps of 0.5V.Press to go back to the previous screen or to continue.nnnnTime+TT°Chh:mm0000sConfirmThe display will show the room temperature TT°C andthe initial counter as 0000s or the time used in theprevious electrofusion cycle (if the unit has not beenturned off). Maximum time of 5940 seconds allowed(99 minutes).Introduce the time indicated by the fitting manufacturer, bearing in mind correction madeaccording to the room temperature (according to the manufacturer). Press the and arrows to move the cursor to another field and the and arrows to select the values.Press to go back to the previous screen or to continue.Edition: April 2012Revision: No. 2 MODE OF USE - 31
Page 1 and 2: USER MANUALELECTROFUSION CONTROL BO
Page 3 and 4: USER MANUALBEAT-HFCONTENTS:CHAPTER
Page 5 and 6: USER MANUALBEAT-HFCHAPTER 1: INTROD
Page 7 and 8: USER MANUALBEAT-HF1.4 UNIT IDENTIFI
Page 9 and 10: USER MANUALBEAT-HF1.6 DECLARATION "
Page 11 and 12: USER MANUALBEAT-HFCHAPTER 2: UNIT
Page 13 and 14: USER MANUALBEAT-HFOn the left side
Page 15 and 16: USER MANUALBEAT-HF3.2 UNIT PREPARAT
Page 17 and 18: USER MANUALBEAT-HF3.2.4 Using the b
Page 19 and 20: USER MANUALBEAT-HFThe following scr
Page 21 and 22: USER MANUALBEAT-HFIf the code intro
Page 23 and 24: USER MANUALBEAT-HFOn the initial sc
Page 25 and 26: USER MANUALBEAT-HFIf the identity o
Page 27 and 28: USER MANUALBEAT-HFOn Read barcode:
Page 29: USER MANUALBEAT-HFnnnnhh:mmPower su
Page 33 and 34: USER MANUALBEAT-HFWARNING !Make sur
Page 35 and 36: USER MANUALBEAT-HF3.5 ACCESS TO OTH
Page 37 and 38: USER MANUALBEAT-HFPENDRIVE-USB/A OP
Page 39 and 40: USER MANUALBEAT-HF4. The PC will fi
Page 41 and 42: USER MANUALBEAT-HFDealing with expo
Page 43 and 44: USER MANUALBEAT-HF Using Microsoft
Page 45 and 46: USER MANUALBEAT-HFSelecting any of
Page 47 and 48: USER MANUALBEAT-HFWatchdd / mm / yy
Page 49 and 50: USER MANUALBEAT-HFJob:Accepting thi
Page 51 and 52: USER MANUALBEAT-HF Service:Finally,
Page 53 and 54: USER MANUALBEAT-HF4.2.2 Fitting res
Page 55 and 56: USER MANUALBEAT-HF4.2.7 Protection
Page 57 and 58: USER MANUALBEAT-HF5.2 MAINTENANCE O
Page 59 and 60: USER MANUALBEAT-HF5.2.4 Updating th
Page 61 and 62: USER MANUALBEAT-HFWith the cursor o
Page 63 and 64: USER MANUALBEAT-HF6.1.2 Generator s

MU-78-10 BEAT-HF - Acuster Bahisa

Create successful ePaper yourself

Delete template?

Save as template?