Manual - AEQ International

More documents

Recommendations

Info

4.5.1. Ethernet Interface configuration.Allows you to configure the IP parameters of the unit manually, when “DHCP” option is “OFF”,or automatically and transparent to the user (by using the DHCP protocol), when that option is“ON” (and the network where the unit is connected to allows to use that protocol). By default,this option is activated (ON). The parameters that should be manually configured when thisoption is deactivated are:• IP Local: IP address of the communication interface.• Gateway: Network gateway to which the equipment is connected.• Mask: Mask associated with that address.• DNS server: IP address of the DNS server (allows you to use host names insteadof IP addresses for both the SIP server and the STUN server).When DHCP option is activated, those four parameters are upgraded showing the valuesautomatically assigned by the network. When you activate it, a question mark appearsnext to the Ethernet interface symbol as well as the “Finding IP address…” messageand both will disappear as soon as the parameters have been assigned; if the network doesn’tallow to use that protocol, the message “DHCP Error” will appear: in that case, the unit keepson trying to obtain that configuration until it gets it or until the DHCP option is deactivated. WhenDHCP option is active we recommend to use our SIP server as intermediary in thecommunications.This configuration must be correctly done for the proper integration of the unit into the IPnetwork that will support communication. If you have any doubts or questions, contact theAuthorized Technical Services or with the System Administrator.4.5.2. 3G Interface configuration.IP Configuration exampleAllows you to configure the 3G interface of the unit, when that communication is establishedthrough a mobile phone connected to USB port. When communication is established through anexternal 3G modem connected to Ethernet port of the unit, that configuration is not necessary.Typically, your mobile phone will be pre-configured with the operator’s APN (Access PointName) in order to function in 3G; all you need to configure in the PHOENIX MOBILE is the username and password requested by your operator in order to have access to 3G connection andthe 3G network tye (UMTS or EV-DO). For further information on this subject, consult annexe Eof this manual.<strong>AEQ</strong> PHOENIX MOBILE48
Detail of 3G Config submenu4.5.3. SIP configuration.This menu covers the configuration of the SIP, SAP and STUN parameters associated with theestablished IP communication, with four submenus called “Parameters“, “Proxy“, “SAPConfiguration“ and “Call Settings”.4.5.3.1. Parameters.This menu enables you to configure certain parameters associated with the SIP protocolimplemented in the unit, as well as all of the STUN protocol parameters. For more informationabout both protocols, we recommend consulting annexe C.<strong>AEQ</strong> PHOENIX MOBILE49
Page 1 and 2: AEQ PHOENIX MOBILEUSER’S MANUALED
Page 3 and 4: 4.3.3.4. Default configuration.....
Page 5 and 6: 1. INTRODUCTION.1.1. General overvi
Page 7 and 8: Coordination ChannelEncoding modesI
Page 9 and 10: 1.5. Compatibility with other AEQ c
Page 11 and 12: 2.1.3. Microphones 1 and 2 input (
Page 13 and 14: 2.2.3. Left additional communicatio
Page 15 and 16: The power supply / battery charger
Page 17 and 18: 1. Multifunction display screen and
Page 19 and 20: ABCDFEGStart-up or idle screen deta
Page 21 and 22: 4.- Section showing inputs/outputs
Page 23 and 24: F1 and F2 function keys: These keys
Page 25 and 26: 2.4. Ethernet Interface.PHOENIX MOB
Page 27 and 28: 2.6. USB Interface.The USB port of
Page 29 and 30: 3. BASIC CONFIGURATION MENU DESCRIP
Page 31 and 32: • Call to: allows you to select w
Page 33 and 34: Each one of the fields that compris
Page 35 and 36: 4.3. Audio settings.The PHOENIX MOB
Page 37 and 38: A routing example in the basic opti
Page 39 and 40: 4.3.2. Input.This menu allows to co
Page 41 and 42: Output menu4.3.3.1. HP1 and HP2.On
Page 43 and 44: 4.4.1. Communication Interfaces ass
Page 45 and 46: 4.4.2.1.2.1. ISDN Configuration.Ins
Page 47: 4.4.2.3. [U].This section will allo
Page 51 and 52: 4.5.3.2. Proxy.This menu includes a
Page 53 and 54: • Media Port: It defines the IP p
Page 55 and 56: • LOW DELAY: Comprehends a set of
Page 57 and 58: 4.7.1. SAP.Details the list of comm
Page 59 and 60: 4.8. Maintenance.Menu of applicatio
Page 61 and 62: MAC ConfigTo edit this information,
Page 63 and 64: 4.9.2. Local Config.Allows you to a
Page 65 and 66: 5. QUICKSTART USER'S GUIDE.To ensur
Page 67 and 68: 5.3. Review of the configuration.On
Page 69 and 70: 5.4.1. Ending an IP communication (
Page 71 and 72: 5.6. Establishment of an ISDN commu
Page 73 and 74: • Select the communication destin
Page 75 and 76: • Once the connection has been co
Page 77 and 78: a) When MICRO (CPU) must be upgrade
Page 79 and 80: 7. TECHNICAL SPECIFICATIONS.*Audio
Page 81 and 82: 8. A.E.Q. WARRANTY.AEQ warrants tha
Page 83 and 84: Comparative graph of different algo
Page 85 and 86: Detailed block diagram of the digit
Page 87 and 88: • The circuit is fixed. Because a
Page 89 and 90: UDP DatagramThe protocols for trans
Page 91 and 92: For complete information on RTP/RTC
Page 93 and 94: This working method, supported by e
Page 95 and 96: PHOENIX MOBILE includes a STUN clie
Page 97 and 98: For complete information on the SAP
Page 99 and 100:
Graphic representation of a DLP pro
Page 101 and 102:
D1.2. Graphics Config.Enables a gra
Page 103 and 104:
ANNEXE E: Connect PHOENIX MOBILE in
Page 105 and 106:
ANNEXE F: 3G and GSM Communications
show all

Manual - AEQ International

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?