Operating Manual LUXOR S 400

More documents

Recommendations

Info

9 Maintenance and repair Maintenance work LUXOR S 400 � Screw the hose [2] back on the nipple of the dry air filter [3]. � The alarm message disappears and the alarm has been canceled. � Disconnect the dry air generator from the power supply. � Replace the lower front panel. 9.5.4 Checking the resistance of the regeneration air heater � Prepare the dry air generator for maintenance (see “Maintenance and repair“ on Page 46). � No power supply is required to measure resistance. � Remove the back panel of the unit. � Measure the resistance on terminal strip –X13E1. � The resistance must be about 34 �. Power Voltage Resistance 9 kW 230/400 V approx. 34 � Fig. 9.6 – Measure resistance 52 Edition: August 2005
LUXOR S 400 Maintenance and repair 9 Maintenance work 9.5.5 Checking/exchanging the temperature limiter The temperature limiter is located in the radiator at the bottom end of the regeneration air heater. The capillary line [4] firmly connected the capillary sensor [1] with the temperature limiter. Fig. 9.7 – Fixing the temperature limiter, capillary sensor Removal � Prepare the dry air generator for maintenance (see “Maintenance and repair“ on Page 46). � Remove the back panel of the unit. � Slacken the screw [3] and remove the locking varnish. � Pull out the capillary sensor on the capillary line [4] and remove with the spring [2]. � Switch the dry air generator on. � Using the hot air blower (no flames), warm up the capillary sensor [1] until an alarm trigger. � The temperature limiter must trip, i.e. the regeneration air heater switches off automatically. The alarm lap illuminates and the message: "Alarm: Regeneration temp. switch tripped out" appears in the display. � If no alarm is tripped, the temperature limiter is defective and must be replaced. � If necessary, unlock the temperature limiter (see “Unlocking temperature limiter“ on Page 68). If the alarm is still pending after resetting the temperature limiter, then this can have one of many causes: � The temperature limiter is defective and must be replaced, or � The temperature on the capillary sensor is still to high. � Wait until the capillary sensor has cooled down. [1] Capillary sensor [2] Spring [3] Screw [4] Capillary line Edition: August 2005 53
Page 1 and 2: Operating Manual CE LUXOR S 400 Dry
Page 3 and 4: LUXOR S 400 5 Structure and functio
Page 5 and 6: LUXOR S 400 Structure and function
Page 7 and 8: LUXOR S 400 Every three years 9.5 M
Page 9: LUXOR S 400 � Switch the dry air
Page 13 and 14: LUXOR S 400 Maintenance and repair
Page 17 and 18: LUXOR S 400 9.6.2 Replacing the bot
Page 21 and 22: LUXOR S 400 Fig. 9.22 - Removing th
Page 23 and 24: LUXOR S 400 � Push the piston rod
Page 25 and 26: LUXOR S 400 9.6.5 Replacing the air
Page 27 and 28: LUXOR S 400 9.6.7 Resetting the pow
Page 29 and 30: 10 Decommissioning and disposal Dis
Page 31 and 32: 11 Options Dew point display LUXOR
Page 33 and 34: 11 Options Fine dust filter LUXOR S
Page 35 and 36: 11 Options Regeneration air cooler
Page 37 and 38: 11 Options Return air cooler LUXOR
Page 39 and 40: 11 Options Return air cooler LUXOR
Page 41 and 42: 12 Appendix Spare parts LUXOR S 400
Page 43 and 44: 12 Appendix Spare parts LUXOR S 400
Page 45 and 46: 12 Appendix Switching valve, regene
Page 47 and 48: 12 Appendix Pneumatics diagram LUXO
Page 49 and 50: 12 Appendix Safety instruction, ads
Page 51 and 52: 8 7 6 5 4 3 2 1 Typenbezeichnung Ba
Page 53 and 54: 8 7 6 5 4 3 2 1 1L1/13.1 1L2/13.1 1
Page 55 and 56: 8 7 6 5 4 3 2 1 /25.3 L+ /27.2 M A
Page 57 and 58: 8 7 6 5 4 3 2 1 /21.1 L+ 18.7/L+ /2
Page 59 and 60: 8 7 6 5 4 3 2 1 A A +TRO -23B1 B B
Page 61 and 62:
8 7 6 5 4 3 2 1 /17.8 L+ 24.8/L+ A
Page 63 and 64:
8 7 6 5 4 3 2 1 +T17 -19A2 +T17 -19
Page 65 and 66:
8 7 6 5 4 3 2 1 A A /19.5 /19.5 /19
show all

Operating Manual LUXOR S 400

Create successful ePaper yourself

Delete template?

Save as template?