EN welding technology

EASY-STICK model range
Valid for EASY-STICKs 131 + 151 + 171
XXThese EASY - STICK devices have a toggle
switch for the operating modes electrode
welding and TIG DC welding
XXFor TIG-DC an internal switch over to
the TIG characteristic curve occurs and
ignition can then use the Lift-Arc system
Scope of supply for EASY-STICK 131, 151, 171
Model EASY-STICK 131 EASY-STICK 151 EASY-STICK 171
Art. no. 1087012 1087014 1087016
Technical data:
Weldable electrode Ø, mm 1.6 - 2.5 1.6 - 3.2 1.6 - 4.0
Electrode setting range 10 - 120 A 10 - 140 A 25 - 160 A
TIG DC setting range 10 - 120 A 10 - 140 A 10 - 160 A
Mains voltage (±10 %) at 50/60 Hz 1 x 230 V 1 x 230 V 1 x 230 V
Frequency 50/60 Hz 50/60 Hz 50/60 Hz
Open circuit voltage 67 V 56 V 67 V
Electrode power consumption 3.0 kVA 3.6 kVA 3.7 kVA
TIG DC power consumption 2.4 kVA 2.7 kVA 2.8 kVA
Fuse 16 A slow blow 16 A slow blow 16 A slow blow
Electrode duty cycle at I max 120A - 40% 140A - 40% 160A -25%
Electrode welding current at DC = 100% 80 A 95 A 115 A
TIG DC duty cycle at I max 120A - 40% 140A - 40% 160A -25%
TIG DC welding current at DC = 100% 80 A 95 A 115 A
Cos phi power factor 0.85 0.85 0.85
Degree of protection IP 23 IP 23 IP 23
Insulation class F F F
Operating temperature -10 +40 °C -10 +40 °C -10 +40 °C
Weight 4.1 kg 4.7 kg 5.2 kg
Dimensions (L x W x H), mm 268 x 120 x 198 290 x 120 x 198 313 x 120 x 198
Schweißkraft equipment has the S mark and complies with standard EN 60 974-1; -10/EMC class A
Argon/CO 2 pressure regulator with content and operation manometer
Schweißkraft small, Ø 50 mm 1700054
Schweißkraft large, Ø 63 mm 1700050
TIG torches and wear part sets for EASY-STICK model range
TIG torches
TIG torch WP 17 V/4m gas regulator 1461745
Pressure regulator
(large)
Degree of protection
IP 23
EASY-STICK 151
Scope of supply EASY-STICK -
SET:
Including welding workplace
equipment
SPA 16 consisting of:
··
5 m welding cable 16 mm² with
electrode holder
··
3m earth cable 16mm² with
earth clamp 200 A
··
Manual shield with welding visor
··
Welders' gloves
··
Chipping hammer
··
Wire brush
··
In an aluminium case
Pressure regulator
small
Grinding
Electrochemical processing Plasma cutting equipment Electrode inverters
TIG inverters
Multifunctional inverters MIG/MAG
Wear part set WP 17 V
consisting of: 1 x each torch cap long/short with o-ring,
2 x Teflon seal, 2 x each clamping sleeve 1.0/1.6/2.4 mm,
2 x each clamping sleeve 1.0/1.6/2.4 mm, 2 x each gas tip size 4/5/6,
2 x each tungsten electrode red 1.0/1.6/2.4 mm, large sorting box
See page 115 for matching welding cables and cables
1463103
WP 17 V
Wear part set
73
Welding accessories