Cable and adapter manual

More documents

Recommendations

Info

MPI-LAN Connection possibilities with operator panel Page 8 Cable and adapter manual © by PI 2009
1.4. Installation Hardware Connect the MPI-LAN cable (short side) with the MPI interface (9 pins) of the S7 - PLC. The network connector from the long side of the cable (RJ – 45) should be connected as described: MPI-LAN cable to computer: Connect the network connector from the MPI cable to the network card interface (RJ – 45) of your computer. MPI-LAN cable to switch/hub: Connect the network connector of the MPI cable to the uplink port of your switch/hub. If you are using an auto - negotiated switch you can put the network connector into a free port of your choice. MPI-LAN with a operator panel: Connect the cable of the operator panel with the PPI/MPI/PROFIBUS – interface of the PLC. Connect the MPI-LAN cable (short side/9 pin plug) with this interface (PPI/MPI/PROFIBUS) so that both cables (MPI-LAN and Operator Panel) are plugged into one interface. Connect the MPI-LAN with the network as described above. There must be a serial communication with the operator panel if this op is new/used at the first time. Therefore connect your operator panel with the serial COM interface of your computer. After the communication has been running successfully the panel is ready to be connected to the PLC. The PLC supports the cable with power. The cable provides an alternative power supply interface which can be connected by a 24V/DC adapter (screw clip or a MPI – net adapter). As soon as the cable is supported with power it shows its software version on the display and begins to test its internal components. Software To communicate with the PLC, please install the PLC - VCom software, as described in chapter 6.2. You also need programming software (e.g. PG 2000, Step© 7, S7 for Windows, Microwin) to work with the PLC. © by PI 2009 Cable and adapter manual Page 9
Page 1 and 2: Version: 5.0 30.11.2009 Cable and a
Page 3 and 4: 4.7.2. Ports.......................
Page 5 and 6: 1.1. Description The MPI-LAN cable
Page 7: MPI-LAN connected with the computer
Page 11 and 12: . Default display (Menu Messages) F
Page 13 and 14: 1.6. Operating instructions Be sure
Page 15 and 16: a. PG 2000 (v4.41) 1. Start the PG
Page 17 and 18: TCP/IP RFC1006 Communication 6. Cli
Page 19 and 20: TCP/IP RFC1006 Configuration 16. Fo
Page 21 and 22: 8. Now you should expand in the „
Page 23 and 24: To clean up errors faster the WinCC
Page 25 and 26: e. Windows Control Center flexible
Page 27 and 28: 9. Press the button „Transfer“
Page 29 and 30: 10. If you want to transfer you pro
Page 31 and 32: If you skipped the point b („Set
Page 33 and 34: 7. In the registry path „Local De
Page 35 and 36: i. S7 for Windows v5.02 Please be s
Page 37 and 38: 1.6.4. Merge two PLCs together by u
Page 39 and 40: Data exchanging with the help of th
Page 41 and 42: 1.6.5. CP - Mode with ProTool/Pro C
Page 43 and 44: 1.6.6. Option Watchdog With this Op
Page 45 and 46: int main(int argc, char* argv[]) {
Page 47 and 48: � °Config° MPI-BUS° MPI interf
Page 49 and 50: • Protocol Change the protocol ve
Page 51 and 52: 1.8. Technical data Type Technical
Page 53 and 54: 2. S7-LAN Ord. No. 9352-LANCon © b
Page 55 and 56: 2.3. Connection possibilities S7-LA
Page 57 and 58: S7 - LAN connection possibilities w
Page 59 and 60:
2.5. Control elements LED for the n
Page 61 and 62:
2.6.1. Using the PLC-VCOM software
Page 63 and 64:
6. Now the software is ready to est
Page 65 and 66:
TCP/IP RFC1006 Communication 6. Cli
Page 67 and 68:
TCP/IP RFC1006 Configuration 16. Fo
Page 69 and 70:
8. Now you should expand in the „
Page 71 and 72:
To clean up errors faster the WinCC
Page 73 and 74:
e. Windows Control Center flexible
Page 75 and 76:
9. Press the button „Transfer“
Page 77 and 78:
10. If you want to transfer you pro
Page 79 and 80:
If you skipped the point b („Set
Page 81 and 82:
7. Confirm your settings with „OK
Page 83 and 84:
i. S7 for Windows v5.02 Please be s
Page 85 and 86:
2.6.3. Direct communication using T
Page 87 and 88:
10. Type in the edit box “Name“
Page 89 and 90:
17. Select the registry card “Ass
Page 91 and 92:
24. A new window opens (the hardwar
Page 93 and 94:
28. Right click on “CPU 312“ in
Page 95 and 96:
33. After you have saved the networ
Page 97 and 98:
2.6.4. Merge two PLCs together by u
Page 99 and 100:
� Format of TXERRRDY and RXERRRDY
Page 101 and 102:
the station supports routing (CPUs
Page 103 and 104:
The S7/MPI-LAN sends only data when
Page 105 and 106:
2.7. Technical data Type Technical
Page 107 and 108:
TS-Function Switches the TeleServic
Page 109 and 110:
MPI/PROFIBUS The MPI/PROFIBUS needs
Page 111 and 112:
Display In this Dialog you could re
Page 113 and 114:
Address Format Input Description FB
Page 115 and 116:
The following operands are possible
Page 117 and 118:
Password Description General Access
Page 119 and 120:
4.1. Description The S5-LAN++ modul
Page 121 and 122:
S5-LAN++ module connected to the co
Page 123 and 124:
4.4. Installation Hardware The S5-L
Page 125 and 126:
2. To start the driver installation
Page 127 and 128:
4.6. Operating instructions Be sure
Page 129 and 130:
4.6.3. Using a PLC software a. PG 2
Page 131 and 132:
. SIMATIC Step© 5 Manager (v5.2 +
Page 133 and 134:
c. Windows Control Center (WinCC) (
Page 135 and 136:
d. Windows Control Center flexible
Page 137 and 138:
Page 139 and 140:
7. In the main window start the Tra
Page 141 and 142:
5. After the software is configured
Page 143 and 144:
8. Select the network interface car
Page 145 and 146:
4.6.5. S5 - Gateway communication R
Page 147 and 148:
4.6.5.1. Specifications of the conf
Page 149 and 150:
In the following example the DB20 w
Page 151 and 152:
4.7.2. Ports Port Type Description
Page 153 and 154:
5.1. Description The MPI-USB cable
Page 155 and 156:
MPI-USB connected to the computer v
Page 157 and 158:
5.4. Installation Hardware Normal i
Page 159 and 160:
. Default Display (Menu Messages) F
Page 161 and 162:
5.6. Operating instructions Be sure
Page 163 and 164:
a. PG 2000 (v4.41) 1. Start the PG
Page 165 and 166:
6. Back in the „Set PG/PC interfa
Page 167 and 168:
c. SIMATIC Step© 7 Manager (v5.2 +
Page 169 and 170:
e. Windows Control Center flexible
Page 171 and 172:
Page 173 and 174:
8. In the main window start the Tra
Page 175 and 176:
If you skipped the point b („Set
Page 177 and 178:
7. In the registry path „Local De
Page 179 and 180:
i. S7 for Windows v5.02 Please be s
Page 181 and 182:
5.6.4. Configuring the operator pan
Page 183 and 184:
. Info Select the menu “Info“ t
Page 185 and 186:
the cables menu) “Lock” in the
Page 187 and 188:
5.8. Technical data Type Technical
Page 189 and 190:
6. PLC - VCom 6.1. Description The
Page 191 and 192:
to go on. 7. After the driver has b
Page 193 and 194:
© by PI 2009 Cable and adapter man
Page 195 and 196:
6.3. Operating instructions Beside
Page 197 and 198:
2 3 4 Press configure in the PLC -
Page 199 and 200:
3 4 5 S5 - Gateway Connections…:
Page 201 and 202:
6.5. MPI-LAN Manager On start up th
Page 203 and 204:
2. Search and click onto your purch
Page 205 and 206:
7.3. Interface Assignment The MPI_D
Page 207 and 208:
6. Select the correct baudrate of t
Page 209 and 210:
7.6. Diagnostics Pressing the butto
Page 211 and 212:
8. Troubleshooting 8.1. Frequently
show all

Cable and adapter manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?