ALUMINUM ELECTROLYTIC CAPACITORS
ALUMINUM ELECTROLYTIC CAPACITORS
ALUMINUM ELECTROLYTIC CAPACITORS
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
LARGE CAPACITANCE <strong>ALUMINUM</strong> <strong>ELECTROLYTIC</strong> <strong>CAPACITORS</strong> Standard snap-ins, 85C<br />
@Endurance with ripple current : 2,000 hours at 85C<br />
@Non solvent resistant type<br />
@RoHS Compliant<br />
?SPACIFICATIONS<br />
Category<br />
Temperature Range<br />
Rated Voltage Range<br />
Capacitance Tolerance<br />
Leakage Current<br />
Dissipation Factor<br />
(tane)<br />
Low Temperature<br />
Characteristics<br />
(Max. Impedance Ratio)<br />
Endurance<br />
Shelf Life<br />
Items<br />
-40 to +85C<br />
6.3 to 100Vdc<br />
P20% (M)<br />
I=0.02CV or 3mA, whichever is smaller.<br />
?PART NUMBERING SYSTEM<br />
Characteristics<br />
Downsized<br />
Longer life<br />
(at 20C, 120Hz)<br />
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)<br />
(at 20C after 5 minutes)<br />
Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V 63V 80V 100V<br />
tanE (Max.)<br />
0.60 0.50 0.40 0.30 0.25 0.20 0.15 0.15 0.15<br />
(at 20C, 120Hz)<br />
Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V 63V 80V 100V<br />
Z(-25C)/Z(+20C) 4 4 4 3 3 2 2 2 2<br />
Z(-40C)/Z(+20C) 15 15 15 10 8 6 6 5 5<br />
(at 120Hz)<br />
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated<br />
ripple current is applied for 2,000 hours at 85C.<br />
Capacitance change [P20% of the initial value<br />
D.F. (tanE) [200% of the initial specified value<br />
Leakage current [The initial specified value<br />
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 85C without<br />
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.<br />
Capacitance change [P20% of the initial value<br />
D.F. (tanE) [150% of the initial specified value<br />
Leakage current [The initial specified value<br />
?DIMENSIONS [mm]<br />
@Terminal Code : VS (F22 to F35) : Standard<br />
FD+1max.<br />
Vent<br />
Sleeve (PET : Black) Negative mark<br />
PC board pin-out<br />
LP2<br />
*FD=35mm : 3.5P0.5mm<br />
*<br />
4.0P0.5<br />
The standard design has no plastic disc.<br />
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18<br />
E S M H A A A V S N A A A M A A A S<br />
Please refer to "Product code guide (snap-in type)"<br />
10<br />
2-F2<br />
FD+1max.<br />
Supplement code<br />
Size code<br />
Capacitance tolerance code<br />
Capacitance code (ex. 820MF:821, 3,300MF:332)<br />
Dummy terminal code<br />
Terminal code<br />
Voltage code (ex. 6.3V:6R3, 63V:630, 100V:101)<br />
Series code<br />
Category<br />
(1/3)<br />
Sleeve (PET : Black)<br />
SMM<br />
SMH<br />
@Terminal Code : LI (F35)<br />
Vent LP2<br />
4.5P1<br />
Negative mark<br />
PC board pin-out<br />
2-1.2B6<br />
14.2P1<br />
4.2P0.5<br />
5P0.5<br />
CAT. No. E1001H