Performance Verification Test Record - LeCroy

More documents

Recommendations

Info

WaveLink Series Differential Probe (13-25 GHz) Connecting the Probe to a LeCroy Oscilloscope The WL-PLink-A Platform/Cable Assembly has been designed for use with the ProLink interface of the LeCroy’s WaveMaster, SDA, WavePro 7 Zi (4 and 6 GHz models), and DDA oscilloscopes; and the WL-2.92MM for use with the 2.92MM interface of the WaveMaster 8 Zi 20-30 GHz oscilloscope models, and their SDA/DDA derivatives. Connecting a WL-PLink-A Platform/Cable Assembly to a WaveMaster 8 Zi Series Oscilloscope Attach the platform/cable assembly to the ProLink interface by aligning the connector with the input connector and pushing the interface toward the instrument. On the WL-PLink-A platform/cable assembly, a click sound is heard when the probe interface latches to the test instrument. The probe also uses thumbscrews to secure the interface to the instrument. Do not overtighten the thumbscrews. Remove the WL-PLink-A platform/cable assembly from the instrument by unscrewing the thumbscrews and moving the interface up and down while pulling gently until a click is heard. This click indicates the platform/cable assembly is detached from the instrument. Connecting a 2.92MM Platform/Cable Assembly to a WaveMaster 8 Zi Series Oscilloscope The WL-2.92MM Platform/Cable Assembly connection consists of a LEMO connector for power and communication and a 2.92mm signal input connector. Make corresponding connections (LEMO, 2.92mm, via included cable) to the 20 - 30 GHz inputs on WaveMaster 820, 825, or 830 Zi oscilloscopes. Connecting a 2.92MM Platform/Cable Assembly to a WaveMaster 8 Zi Series Oscilloscope using the LPA-2.92 ProLink to 2.92MM Probe Adapter Some LeCroy oscilloscopes utilize both ProLink and 2.92 mm inputs. In this case, a single WL- 2.92MM platform/cable assembly can be used for all types of high bandwidth inputs and an LPA-2.92 to ProLink adapter can be used to connect the WL-2.92MM to a ProLink communication, power and signal interface. Operation with a LeCroy Oscilloscope PLEASE NOTE THE FOLLOWING: � Download the latest version of X-Stream software to run your WaveLink probe with maximum performance. � Ensure your Windows updates are current. WL-HBW-OM-E RevC 24
� If utilizing the probe with an SDA 9000, 11000, 13000, or 18000 oscilloscope, download and install the most recent version of the Microsoft Core XML Services (MSXML) Service Pack before using your probe. Other supporting service packs may be required for MSXML to work properly. Figure 4-3. Vertical dialog with labeled tab corresponding with your attached probe. When the probe platform/cable assembly is connected to a probe amplifier module, and this assembly is then attached to an X-Stream oscilloscope’s input, the oscilloscope recognizes the probe and activates the vertical channel functions in the user interface (shown previous). Refer to your oscilloscope’s instruction manual for specific operation. Control through the oscilloscope’s interface can be found on the channel dialog that corresponds with the connected probe. Touching the tab for the attached probe (varies based on the particular probe you have attached) activates the probe dialog as follows. The probe information frame shows the characteristics of the probe. Touching the Power On checkbox turns the probe power on or off. 25 WL-HBW-OM-E RevC
Page 1 and 2: Operator’s Manual WaveLink Series
Page 3 and 4: LeCroy Corporation 700 Chestnut Rid
Page 5 and 6: Accessory Overview ................
Page 7 and 8: Introduction LeCroy’s WaveLink 13
Page 9 and 10: Platform/Cable Assembly, Amplifier
Page 11 and 12: Figure 3-2. WL-2.92MM The Platform/
Page 13 and 14: Since a pure distributed amplifier
Page 15 and 16: Amplifier Modules (includes solder-
Page 17 and 18: Two replacement resistive tips are
Page 19 and 20: This simplifies the purchase of cor
Page 21 and 22: Handling the Probe The WaveLink ser
Page 23: Connecting an Amplifier Module to a
Page 27 and 28: Tip Select Make the appropriate sel
Page 29 and 30: Solder-In Interconnect Lead The Sol
Page 31 and 32: 2. Now, bend the tips in toward the
Page 33 and 34: Various attachments and extenders a
Page 35 and 36: AutoColor ID and Power Control Indi
Page 37 and 38: EZ Probe Positioner The EZ Probe Po
Page 39 and 40: Dxx0-PT-XYZ-POSITIONER This positio
Page 41 and 42: MOVING AND POSITIONING Always apply
Page 43 and 44: PLATFORM/CABLE ASSEMBLY BOARD EDGE
Page 45 and 46: Probe Deskew Fixture The Probe Desk
Page 47 and 48: Replacing Damping Resistors on the
Page 49 and 50: 4. Verify the following dimensions
Page 51 and 52: Occasionally check the overall resi
Page 53 and 54: PLEASE NOTE THE FOLLOWING: � Tips
Page 55 and 56: Service Strategy Defective probes o
Page 57 and 58: Description and Initial Product Cod
Page 59 and 60: Description and Initial Product Cod
Page 61 and 62: Service Option Product Code Three-Y
Page 63 and 64: 3. Turn on the channel correspondin
Page 65 and 66: 14. Verify the screen shows a squar
Page 67 and 68: If the probe package includes probe
Page 69 and 70: Description Minimum Requirements Te
Page 71 and 72: 8. After a warm-up time of at least
Page 73 and 74: connected channel has the correct B
Page 75 and 76:
� Unplug the BNC to Banana Plug A
Page 77 and 78:
3. Connect the SI Probe tip to the
Page 79 and 80:
You can also find contact informati
Page 81 and 82:
Safety Requirements CAUTION Avoid p
Page 83 and 84:
These circuits represent the aggreg
Page 85 and 86:
Figure 9-3. Typical probe input imp
Page 87 and 88:
Probe Impedance - LeCroy Dxx05 Prob
Page 89 and 90:
Exceeding the common mode range can
Page 91 and 92:
Offset Offset for D1305, D1605, D20
Page 93 and 94:
Attenuation Accuracy Step Descripti
Page 95 and 96:
O operating environment, 81 Operati
show all

Performance Verification Test Record - LeCroy

Create successful ePaper yourself

Delete template?

Save as template?