Performance Verification Test Record - LeCroy

More documents

Recommendations

Info

WaveLink Series Differential Probe (13-25 GHz) Figure 5-8. Insert the probe body into the board edge clip and position the clamp as desired. ADHESIVE BACKED PLATFORM/CABLE ASSEMBLY CLAMPS (4) The Adhesive Backed Probe Body Clamp provides additional support to the Platform/Cable Assembly and Interconnect Lead anywhere on the board under test. Connection Guides Probe connection guides are designed to make it easy to electrically isolate the two probe tips when browsing. They also greatly reduce accidental and unwanted contact across probe points. Before attaching connection guides, clean the PCA assembly area with IPA or another cleaner to remove oils. Then, apply with a light pressure, release, and let set for one hour. WL-HBW-OM-E RevC 44
Probe Deskew Fixture The Probe Deskew Fixture (PCF200) is provided as a standard accessory with WaveLink series Platform/Cable Assemblies. The fixture can be used one of two ways: 1. For lower bandwidth WaveLink probes (≤ 6 GHz), the fixture may be used to determine the effect of probe input loading on the circuit under test and the probe response to the signal being measured, using the D610, D620, D310, and D320 modules. 2. For all WaveLink probes designed to accommodate all WaveLink tips (not at full bandwidth), the fixture may be used as a convenient way to deskew several probes/oscilloscope channels. This can be accomplished in the following ways: � Connect a fast edge to one or both inputs. Connect the probe tip(s) to the appropriate connection point. Solder-in probe tips and browser tips may be inserted under the clamping mechanism. Display the probe signals on the oscilloscope screen and use the channel deskew adjust to align them to a common point. � Connect the WavePro 7 Zi or WaveMaster 8 Zi fast edge output to one of the inputs. Set the Zi Series oscilloscope to trigger on the internal Fast Edge source. Set the trigger delay to zero. Now, on the vertical dialog, use the Probe Cal - Cable Deskew button to align one signal/channel at a time to the specified zero delay trigger point (center of screen). Repeat for as many probes as you have connected, each time aligning them to the common point. Note: The Probe Deskew fixture has an inherent rise time limitation of ~70ps. Deskew of very high frequency signals using WaveLink High Bandwidth Differential Probes may require a faster rise time than this fixture can provide. In this case, utilize one of your signals as a reference point, and then deskew all additional signals to the reference signal. 45 WL-HBW-OM-E RevC
Page 1 and 2: Operator’s Manual WaveLink Series
Page 3 and 4: LeCroy Corporation 700 Chestnut Rid
Page 5 and 6: Accessory Overview ................
Page 7 and 8: Introduction LeCroy’s WaveLink 13
Page 9 and 10: Platform/Cable Assembly, Amplifier
Page 11 and 12: Figure 3-2. WL-2.92MM The Platform/
Page 13 and 14: Since a pure distributed amplifier
Page 15 and 16: Amplifier Modules (includes solder-
Page 17 and 18: Two replacement resistive tips are
Page 19 and 20: This simplifies the purchase of cor
Page 21 and 22: Handling the Probe The WaveLink ser
Page 23 and 24: Connecting an Amplifier Module to a
Page 25 and 26: � If utilizing the probe with an
Page 27 and 28: Tip Select Make the appropriate sel
Page 29 and 30: Solder-In Interconnect Lead The Sol
Page 31 and 32: 2. Now, bend the tips in toward the
Page 33 and 34: Various attachments and extenders a
Page 35 and 36: AutoColor ID and Power Control Indi
Page 37 and 38: EZ Probe Positioner The EZ Probe Po
Page 39 and 40: Dxx0-PT-XYZ-POSITIONER This positio
Page 41 and 42: MOVING AND POSITIONING Always apply
Page 43: PLATFORM/CABLE ASSEMBLY BOARD EDGE
Page 47 and 48: Replacing Damping Resistors on the
Page 49 and 50: 4. Verify the following dimensions
Page 51 and 52: Occasionally check the overall resi
Page 53 and 54: PLEASE NOTE THE FOLLOWING: � Tips
Page 55 and 56: Service Strategy Defective probes o
Page 57 and 58: Description and Initial Product Cod
Page 59 and 60: Description and Initial Product Cod
Page 61 and 62: Service Option Product Code Three-Y
Page 63 and 64: 3. Turn on the channel correspondin
Page 65 and 66: 14. Verify the screen shows a squar
Page 67 and 68: If the probe package includes probe
Page 69 and 70: Description Minimum Requirements Te
Page 71 and 72: 8. After a warm-up time of at least
Page 73 and 74: connected channel has the correct B
Page 75 and 76: � Unplug the BNC to Banana Plug A
Page 77 and 78: 3. Connect the SI Probe tip to the
Page 79 and 80: You can also find contact informati
Page 81 and 82: Safety Requirements CAUTION Avoid p
Page 83 and 84: These circuits represent the aggreg
Page 85 and 86: Figure 9-3. Typical probe input imp
Page 87 and 88: Probe Impedance - LeCroy Dxx05 Prob
Page 89 and 90: Exceeding the common mode range can
Page 91 and 92: Offset Offset for D1305, D1605, D20
Page 93 and 94: Attenuation Accuracy Step Descripti
Page 95 and 96:
O operating environment, 81 Operati
show all

Performance Verification Test Record - LeCroy

Create successful ePaper yourself

Delete template?

Save as template?