Infineon SAB 80C517A, SAB 83C517A-5 User's Manual ... - Keil

More documents

Recommendations

Info

Edition 05.94 This edition was realized using the software system FrameMaker ® . Published by Siemens AG, Bereich Halbleiter, Marketing- Kommunikation, Balanstraße 73, 81541 München © Siemens AG 1994. All Rights Reserved. Attention please! As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or the Siemens Companies and Representatives worldwide (see address list). Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Siemens Office, Semiconductor Group. Siemens AG is an approved CECC manufacturer. Packing Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1 of the Semiconductor Group of Siemens AG, may only be used in life-support devices or systems 2 with the express written approval of the Semiconductor Group of Siemens AG. 1 A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered.
SAB 80C517A/83C517A-5 Revision History: 05.94 Previous Version: 11.92 Page Subjects (major changes since last revision 11.92) 3-8 S0RELL adresses corrected 4-1 HWPD pin number corrected 5-3 TS/TC in table 5-1 corrected 5-10/5-11 CC4EN bit names and table 5-3 corrected Device Specifications SAB 80C517A/83C517A-5 Revision History: 05.94 Previous Releases: 01.94/08.93/11.92/10.91/04.91 Page Subjects (changes since last revision 04.91) 5 Pin configuration P-MQFP-100-2 added 4 Pin differences updated 6-14 Pin numbers for P-MQFP-100-2 package added several Correction of P-MRFP-100 into P-MQFP-100-2 2 Ordering information for – 40 to + 110 °C versions 25,26,30 Correction of register names S0RELL, SCON, ADCON, ICRON and SBUF 33 Figure 4 corrected 39 Figure 8 corrected 57 PE/SWD function description completed 60 Correct ordering numbers 62 Test condition for VOH, VOH1 corrected 65 tPXIZ name corrected tAVIV, tAZPL values corrected several Minimum clock frequence is now 3.5 MHz 66 68 tQVWH (data setup before WR) corrected and added tLLAX2 corrected Page Subjects (changes since last version 08.93) 25 51 65 67 74 Corrected SFR name S0RELL Below “Termination of HWPD Mode”: 4th paragraph with ident corrected Description of t LLIV corrected Program Memory Read Cycle: f PXAV added Oscillator circuit drawings: MQFP-100-2 pin numbers added. Page Subjects (changes since last revision 01.94) 47 Minor changes on several pages Table 6 corrected
Page 1: Microcomputer Components SAB 80C517
Page 5 and 6: 1 Introduction The SAB 80C517A is a
Page 7 and 8: 2 Fundamental Structure The SAB 80C
Page 9 and 10: 3 Memory Organization Semiconductor
Page 11 and 12: 3.2 Data Memory Semiconductor Group
Page 13 and 14: Table 3-1, Special Function Registe
Page 15 and 16: Table 3-1, Special Function Registe
Page 17 and 18: 3.4 Architecture for the XRAM Semic
Page 19 and 20: Figure 3-2 Write Page Address to Po
Page 21 and 22: Figure 3-4 Use of Port 2 as I/O-Por
Page 23 and 24: 3.4.2 Control of XRAM in the SAB 80
Page 25 and 26: EA = 0 EA = 1 XMAP1, XMAP0 XMAP1, X
Page 27 and 28: Table 4-1, Status of all Pins Durin
Page 29 and 30: 4.2 Hardware Power Down Reset Timin
Page 31 and 32: Figure 4-2 Timing Diagram of Leavin
Page 33 and 34: 4.3 Fast internal Reset after Power
Page 35 and 36: Figure 4-4 Power-On of the SAB 80C5
Page 37 and 38: Semiconductor Group 5 - 2 On-Chip P
Page 39 and 40: Figure 5-1 10-Bit A/D-Converter Sem
Page 41 and 42: Special Function Register ADDATH, A
Page 43 and 44: 5.3 Additional Compare Mode for the
Page 45 and 46: Special Function Register CC4EN Bit
Page 47 and 48: Semiconductor Group 5 - 12 On-Chip
Page 53 and 54:
Special Function Register SRELH, SR
Page 55 and 56:
Detailled Description of the Oscill
Page 57 and 58:
6 Interrupt System 6.1 Additional I
Page 59 and 60:
Special Function Register IRCON1 Bi
Page 61 and 62:
3.1 Priority Level Structure The fo
Page 63 and 64:
4 Device Specification Device Speci
Page 65 and 66:
Logic Symbol Semiconductor Group 7-
Page 67 and 68:
Pin Configuration (P-MQFP-100-2) Se
Page 69 and 70:
Pin Definitions and Functions (cont
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Figure 1 Block Diagram Semiconducto
Page 79 and 80:
Semiconductor Group 7-17 Device Spe
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
s Table 1: Behaviour of P0/P2 and R
Page 87 and 88:
Page 89 and 90:
Table 2 Special Function Register (
Page 91 and 92:
Table 3 Special Function Registers
Page 93 and 94:
Table 3 Special Function Registers
Page 95 and 96:
Figure 4 Block Diagram A/D Converte
Page 97 and 98:
Table 4 CCU Compare Configuration S
Page 99 and 100:
Page 101 and 102:
Figure 6 Block Diagram of Timer 2 S
Page 103 and 104:
Figure 9 Compare-Mode 2 (Port 5 onl
Page 105 and 106:
Figure 10 Interrupt Structure of th
Page 107 and 108:
Figure 10 Interrupt Structure of th
Page 109 and 110:
Table 6 Performing a MDU-Calculatio
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Serial Interface 0 Serial Interface
Page 119 and 120:
Page 121 and 122:
Figure 12 Functional Block Diagram
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
ALE PSEN Port 0 Port 2 Program Memo
Page 131 and 132:
AC Characteristics (cont’d) Exter
Page 133 and 134:
ROM Verification Characteristics TA
Page 135 and 136:
Application Circuitry for Verifying
Page 137:
Package Outlines Plastic Package, P
show all

Infineon SAB 80C517A, SAB 83C517A-5 User's Manual ... - Keil

Create successful ePaper yourself

Delete template?

Save as template?