Accela Pump Hardware Manual

More documents

Recommendations

Info

2 Installation Making the Initial Back Panel Connections Connecting the Power Cable Connecting the USB Cable The pump is shipped with a power cord appropriate for the shipping destination. CAUTION Never connect the pump to, or operate the pump with, an electrical line source that has power drops or fluctuations of 10% below the nominal rated line voltage. � To connect the pump to line power 1. Connect the power cord to the line power receptacle on the back panel of the pump. 2. Connect the power cord to an appropriate line power source. The Accela Pump Accessory Kit contains a USB cable that is approximately 3 m long. � To connect the pump to the computer with the USB cable 1. Connect the series A plug of the USB cable to an available USB port on the computer. Figure 7 shows the USB plugs and sockets. Figure 7. USB plugs and sockets Series A socket Series B socket Series A plug Series B plug 2. Connect the series B plug of the USB cable to the USB port on the back of the Accela Pump. 14 Accela Pump Hardware Manual Thermo Scientific
Connecting the System Interconnect Cable 2 Installation Making the Initial Back Panel Connections The system interconnect cable synchronizes the timing of the Accela devices. The interconnect cable has seven combicon connectors: three are labeled DETECTOR; two are labeled PUMP; one has a small, A/S tag on its adjacent cable; and one has a small, M/S tag on its adjacent cable (see Figure 8). Figure 9 shows the connections to the system modules. Figure 8. System interconnect cable with seven combicon connectors M/S Autosampler connector � To connect the system interconnect cable DETECTOR 1. Plug one of the pump connectors with a yellow PUMP sticker into the 8-pin socket on the back panel of the Accela Pump. 2. Plug the autosampler connector with the A/S tag on its adjacent cable into the left, 8-pin socket on the back panel of the Accela Autosampler. 3. If your LC system contains an Accela PDA Detector, plug one of the detector connectors with a blue DETECTOR sticker into the left, 8-pin socket on the back panel of the detector. IMPORTANT You can use the older 5-connector version of the system interconnect cable with Accela LC system. If you use the cable that has 5-combicon connectors, attach the connector that has a blue, LC PUMP label to the Accela Pump. Thermo Scientific Accela Pump Hardware Manual 15 PUMP A/S DETECTOR DETECTOR PUMP
Page 1 and 2: Accela Pump Hardware Manual 60157-9
Page 3 and 4: Regulatory Compliance Thermo Fisher
Page 5 and 6: WEEE Compliance This product is req
Page 7 and 8: CAUTION Symbol CAUTION VORSICHT ATT
Page 9 and 10: Contents Thermo Scientific Accela P
Page 11: Baseline Noise at Low Pressures. .
Page 14 and 15: Preface Special Precautions for the
Page 16 and 17: Preface Solvent Requirement Many ch
Page 19 and 20: Introduction The Accela Pump is a m
Page 21 and 22: The following topics describe the m
Page 23 and 24: Pulse Dampening Assembly 1 Introduc
Page 25 and 26: Status LEDs 1 Introduction Function
Page 27 and 28: Installation This chapter provides
Page 29 and 30: Unpacking and Inspecting the Instru
Page 31: Making the Initial Back Panel Conne
Page 35 and 36: Connecting the Low-Pressure Solvent
Page 37 and 38: Installing the Super Flangeless Fit
Page 39 and 40: d. Unscrew the swaged fitting and v
Page 41 and 42: Figure 18. Connection between the p
Page 43 and 44: Data System Instrument Configuratio
Page 45 and 46: Figure 20. Thermo Foundation Instru
Page 47 and 48: 3 Data System Instrument Configurat
Page 49 and 50: The Instrument Configuration dialog
Page 51 and 52: 6. Configure the Accela Pump option
Page 53: 3 Data System Instrument Configurat
Page 56 and 57: 4 Preparing the Pump for Operation
Page 58 and 59: 4 Preparing the Pump for Operation
Page 61 and 62: Diagnostics Use the following proce
Page 63 and 64: Using ChromQuest to Monitor the Pum
Page 65 and 66: 5 Diagnostics Testing the Pump Prop
Page 67 and 68: Determining the Delay Volume of the
Page 69: 5 Diagnostics Determining the Delay
Page 72 and 73: 6 Maintenance Flushing the Piston G
Page 74 and 75: 6 Maintenance Minimizing Pump Pulsa
Page 76 and 77: 6 Maintenance Cleaning the LDA Comp
Page 78 and 79: 6 Maintenance Removing the LDA from
Page 80 and 81: 6 Maintenance Removing the LDA from
Page 82 and 83:
6 Maintenance Disassembling the LDA
Page 84 and 85:
6 Maintenance Disassembling the LDA
Page 86 and 87:
6 Maintenance Replacing the Primary
Page 88 and 89:
6 Maintenance Assembling the Liquid
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
6 Maintenance Connecting the LDA to
Page 96 and 97:
6 Maintenance Servicing the Proport
Page 98 and 99:
6 Maintenance Replacing a Fuse Repl
Page 100 and 101:
7 Troubleshooting General System Tr
Page 102 and 103:
7 Troubleshooting Pump Troubleshoot
Page 104 and 105:
7 Troubleshooting Pump Troubleshoot
Page 106 and 107:
7 Troubleshooting Baseline Noise at
Page 108 and 109:
7 Troubleshooting Irreproducible Re
Page 110 and 111:
8 Accessories and Replacement Parts
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 119 and 120:
Discontinued Versions of the Accela
Page 121 and 122:
Figure 74. Installing the PEEK film
Page 123:
A Discontinued Versions of the Acce
Page 126 and 127:
Index: E delay volume determining 4
Page 128:
Index: T steel compression ring 20
show all

Accela Pump Hardware Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?