parts identification

More documents

Recommendations

Info

Step 23 49 49 N5 N8 N5 H170 H170 49 90 Bracket & Handle Installation 1. Attach Safety Handles (N5) to Rail Uprights with Handle Holes (49) using 1/4" Hardware (H170). *NOTE: Pre-drill 1/2" deep holes for #14 Hardware (H163) (H164) with a 1/8" drill bit. *NOTE: Position 90 Brackets so that the Hardware does not hit the gaps between the Deck Boards. 2. Position 90 Brackets (N8) on Deck and up against Rail Uprights with Handle Holes (49) and attach using #14 Hardware (H163) (H164). The #14 Hardware (H163) must go through the 90 (N8) and into the Deck (as shown in Detail A). A total of six 90 Brackets (N8) should be installed in this step. N8 Shorter #14 Hardware here N5 H163 H164 N8 42 49 49 N8 49 N8 N5 DETAIL A 49 49 H163 H164
Step 24 H176 3 75 90 90 93 H152 112 H152 90 90 106 94 93 71 H152 Cabin Package Assembly 1. Center and attach Cabin Upright (106) between Corner Uprights (75) to 2 Hole Facia (112) and Single Arched Facia (71) using #8 Hardware (H152). Measure over approximately 16 1/8" from Corner Upright (75). *NOTE: Measure up 26 1/2" from the top of the Deck to the Bottom of Cabin Upright (106). 2. Position Cabin Uprights (90) up against the Corner Uprights (75), Cabin Upright (106) and attach to 2 Hole Facia (112) and Single Arched Facia (71) using #8 Hardware (H152). Cabin Uprights should rest on the top of Rail Uprights (3) when properly installed. 3. Center and attach Window Vertical (94) between Cabin Uprights (90) to 2 Hole Facia (112) and Single Arched Facia (71) using #8 Hardware (H152). 4. Center Window Horizontal (93) between 2 Hole Facia (112) and Single Arched Facia (71) and attach to Cabin Uprights (90) and Window Vertical (94) using #8 Hardware (H176). *NOTE: Make sure that #8 Hardware (H176) is used to attach Window Horizontal (93). 5. Repeat #1 through #4 for the other side. 16 1/8" 43 94 EDGES FLUSH 90 H176 112 75 90 3 112 93 90 94
Page 1 and 2: Contains Assembly, Use, and Mainten
Page 3 and 4: OWNER'S MANUAL Sunray Premium Playg
Page 5 and 6: Choosing a location & protective su
Page 7 and 8: 9. Check the C-Links on the chain t
Page 9 and 10: PARTS IDENTIFICATION 77 78 82 81 86
Page 11 and 12: *NOTE: Extra hardware is included i
Page 13 and 14: H60 Hardware for Assembly *NOTE: Th
Page 15 and 16: 34 35 2@ 5/8" x 3 3/8" x 14 3/16" L
Page 17 and 18: 69 73 70 72 71 116 74 75 77 80 83 8
Page 19 and 20: N29 N73 N18 N14 14@ 3/8" 2@ Small B
Page 21 and 22: Step 1 continued from previous page
Page 23 and 24: H108 Step 3 75 1/2" 75 H1 68 73 46
Page 25 and 26: Step 5 67 Deck Assembly 1. Center a
Page 27 and 28: Step 6 DECK BOARDS NOT SHOWN FOR CL
Page 29 and 30: Step 8 N8 DETAIL A 69 N8 A H164 51
Page 31 and 32: Step 10 1. Position Ladder Assembly
Page 33 and 34: Step 12 H176 40 49 7/8" 16 41 NOTE
Page 35 and 36: Step 14 40 43 13/16" 16 44 40 44 NO
Page 37 and 38: Step 16 DETAIL A H155 65 H155 Upper
Page 39 and 40: Step 18 H176 12 64 H152 11 14 10 63
Page 41 and 42: Step 20 93 95 Bay Window Assembly 1
Page 43: Step 22 113 3 113 H154 83 49 49 3 1
Page 47 and 48: Step 26 Rock Wall Assembly 1. Lay 2
Page 49 and 50: Step 27 N9 5 Rock Wall Assembly 1.
Page 51 and 52: Step 29 N12 N30 N13 12" INSET A Tir
Page 53 and 54: Step 31 1. On the ground, place Swi
Page 55 and 56: Step 32 60 36 62 H176 36 H176 37 37
Page 57 and 58: Step 34 63 74 100 103 64 46 Bubble
Page 59 and 60: Step 36 SINGLE KNOTS Rock Wall Rope
Page 61 and 62: Step 38 *NOTE: Pre-drill holes for
Page 63 and 64: Step 41 STAKE STAKE INSET A Stake I
Page 65 and 66: Limited Ten-Year & Limited One-Year
Page 67 and 68: If you would like to order replacem

parts identification

Create successful ePaper yourself

Delete template?

Save as template?