parts identification

More documents

Recommendations

Info

Step 25 H1 1 1/2" 74 104 46 H108 74 Store Front Assembly *NOTE: Pre-drill holes for all 5/16" Lag Bolts with a 1/8" drill bit. 1. Measure up 23 1/2" on Corner Uprights (74) (on the Top Joist side) and attach 2 Hole Facia (46) using 1/4" Hardware (H1) and 5/16" Hardware (H108). 2. Attach Arched Facia (104) to Corner Uprights (74) up against the bottom of the Deck Facia (69) using #8 Hardware (H152). 3. From the top of the 2 Hole Facia (46) measure down 1 1/2". Evenly gap Store Front Uprights (4) (39) between Corner Uprights (74) (as shown) and attach to 2 Hole Facia (46) and 4 Hole Facia (73) using #8 Hardware (H152). 4 H1 69 H152 H108 23 1/2" 44 39 46 H152 73
Step 26 Rock Wall Assembly 1. Lay 2 Hole Rock Wall Boards (8), Inside 2 Hole Rock Wall Boards (6) and Rock Wall Legs (66) on a flat surface. Use a hammer to pound in 1/4" Hardware (H32) and 3/8" Hardware (H34) (as shown in Inset A). Rock Wall Legs must be orientated as shown in Inset A. 2. On a flat surface, lay Rock Wall Legs (66) on edge with holes up. Ends should be flush, and Hardware (H34) should be on the outside of each Rock Wall Leg (66) (as shown). Rock Wall Legs should be positioned so they measure 34 1/2" apart from outside face to outside face. *NOTE: The top two Rock Wall Boards (6) will be installed in the next step after the Rock Wall is attached to the set. *NOTE: 1/4" Hardware (H32) must be on the bottom side when Rock Wall Boards are attached. 3. Attach Rock Wall Board (7) to Rock Wall Legs (66), 6 1/2" down from the top of the Rock Wall Legs (66), using #8 Hardware (H152) in the top two holes only at this time. 4. Position the remaining Rock Wall Boards (6) (7) (8) (except for the top two Rock Wall Boards) along the Rock Wall Legs in the order shown. Rock Wall Boards should be tight against each other and should not have gaps between boards. 5. Check to make sure Rock Wall Legs (66) are still 34 1/2" apart and attach Rock Wall Board w/Rope Hole (9) to Rock Wall Legs using #8 Hardware (H152) in the bottom two holes only at this time. 6. Measure diagonally across the Rock Wall assembly and make adjustments as needed to ensure that the Rock Wall is square. 7. Finish attaching Rock Wall Board w/Rope Holes (9) and top Rock Wall Board (7). Continue attaching Rock Wall Boards (6) (7) (8) in the order shown using #8 Hardware (H152). 8. Position Top Rock Wall Board (5) on top edge of Rock Wall Legs (66) with the back edges flush and attach using # 8 Hardware (H152). 9. Center and attach Rock Wall Runner (50) to the back side of Rock Wall Boards (6) (7) (8) (9) using Hardware (H152). Runner (50) should be pushed up against the under side of the Top Rock Wall Board (5). *NOTE: Rocks (N21) must go on the side of the Rock Wall Board opposite the 1/4" Hardware (H32). *SUGGESTION: Use a manual screw driver to attach Rocks (N21). 10. Attach Rocks (N21) to Rock Wall Boards (6) (8) using 1/4" Hardware (H7) (H170) (H32) (as shown in Inset B). *NOTE: Avoid over-tightening Hardware on Rocks so the Hardware doesn't protrude out the back side. 11. Attach 90 Ladder Brackets (N9) to Rock Wall Legs (66) using 3/8" Hardware (H34) (H11) (H124) (as shown in Detail B). *NOTE: Do not fully tighten Ladder Bracket Hardware at this time. 45 continued on next page:
Page 1 and 2: Contains Assembly, Use, and Mainten
Page 3 and 4: OWNER'S MANUAL Sunray Premium Playg
Page 5 and 6: Choosing a location & protective su
Page 7 and 8: 9. Check the C-Links on the chain t
Page 9 and 10: PARTS IDENTIFICATION 77 78 82 81 86
Page 11 and 12: *NOTE: Extra hardware is included i
Page 13 and 14: H60 Hardware for Assembly *NOTE: Th
Page 15 and 16: 34 35 2@ 5/8" x 3 3/8" x 14 3/16" L
Page 17 and 18: 69 73 70 72 71 116 74 75 77 80 83 8
Page 19 and 20: N29 N73 N18 N14 14@ 3/8" 2@ Small B
Page 21 and 22: Step 1 continued from previous page
Page 23 and 24: H108 Step 3 75 1/2" 75 H1 68 73 46
Page 25 and 26: Step 5 67 Deck Assembly 1. Center a
Page 27 and 28: Step 6 DECK BOARDS NOT SHOWN FOR CL
Page 29 and 30: Step 8 N8 DETAIL A 69 N8 A H164 51
Page 31 and 32: Step 10 1. Position Ladder Assembly
Page 33 and 34: Step 12 H176 40 49 7/8" 16 41 NOTE
Page 35 and 36: Step 14 40 43 13/16" 16 44 40 44 NO
Page 37 and 38: Step 16 DETAIL A H155 65 H155 Upper
Page 39 and 40: Step 18 H176 12 64 H152 11 14 10 63
Page 41 and 42: Step 20 93 95 Bay Window Assembly 1
Page 43 and 44: Step 22 113 3 113 H154 83 49 49 3 1
Page 45: Step 24 H176 3 75 90 90 93 H152 112
Page 49 and 50: Step 27 N9 5 Rock Wall Assembly 1.
Page 51 and 52: Step 29 N12 N30 N13 12" INSET A Tir
Page 53 and 54: Step 31 1. On the ground, place Swi
Page 55 and 56: Step 32 60 36 62 H176 36 H176 37 37
Page 57 and 58: Step 34 63 74 100 103 64 46 Bubble
Page 59 and 60: Step 36 SINGLE KNOTS Rock Wall Rope
Page 61 and 62: Step 38 *NOTE: Pre-drill holes for
Page 63 and 64: Step 41 STAKE STAKE INSET A Stake I
Page 65 and 66: Limited Ten-Year & Limited One-Year
Page 67 and 68: If you would like to order replacem

parts identification

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?