Bell & Howell - Projector - Filmosound 641 - 642 ... - Cine Information
Bell & Howell - Projector - Filmosound 641 - 642 ... - Cine Information
Bell & Howell - Projector - Filmosound 641 - 642 ... - Cine Information
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Disassemble parts shown in Figures 42<br />
-45 in their indexed order and note the<br />
following precautions.<br />
When the actuating assembly (13/<br />
Fig.44) is removed/ observe the setscrew<br />
protruding up from the casting immediately<br />
below the mounted position of the<br />
actuating assembly. The height of this<br />
setscrew above the casting has been set<br />
to ensure that the auto-threading system<br />
does not lock when the actuating assembly<br />
is depressed. Do not disturb this setscrew.<br />
Before disassembling/ make a careful note<br />
of the manner in which the various springs<br />
(9/ 15/ 18 and 44 Fig.45) are installed. It<br />
is important that these springs be reassembled<br />
in the same manner.<br />
Removal of parts in this illustration will<br />
necessitate the re-adjustment of the autothreading<br />
mechanism as described later.<br />
REASSEMBLING THE MECHANISM (Figure 45)<br />
Install lens stop screw (67) into the housing<br />
casting until only one thread is visible.<br />
Attach lens carrier catch (65) and spacer<br />
washer (66) to casting with screws (63) and<br />
lock washer (64). The stop screw and catch<br />
will be adjusted after lens carrier is installed.<br />
Secure the connecting link (60) and shuttle<br />
retractor (59) to the casting with screw (56)<br />
and washers (57 and 58).<br />
Attach self-centering assembly (55) to rear<br />
of casting with screws (52) and washers (53 and<br />
54). Assemble lever and shaft assembly (51)<br />
to casting and install washer (42) and<br />
arm assembly (50) on shaft. Tighten screw<br />
(49).<br />
69<br />
Assemble cam follower parts (48) and<br />
fasten to the arm assembly (50) with screw<br />
(45) and washers (46 and 47). Attach<br />
spring (44) to casting and hook loose end<br />
of spring over shaft of lever assembly (51).<br />
Assemble upper loop form shaft (68) to<br />
casting and install washer (42) and upp<br />
loop form (41); tighten setscrews (35).<br />
Install upper sprocket guard plate (40).<br />
Assemble lower loop form (38) so that<br />
loop form shaft passes through guard plate<br />
and casting while upper stud of connecting<br />
link passes through holes in upper loop<br />
form. Install retaining ring (37) on<br />
connecting link stud and the threading<br />
lever (36) on end of loop form shaft.<br />
Secure the threading lever with setsc m<br />
(35).<br />
Install spring (34) so that it supplies return<br />
tension to shaft (68).<br />
Assemble toggle lever (31) to lower<br />
sprocket guard plate (28) with retaining<br />
ring (30). Fasten guard plate to casting<br />
screws (27). Install upper film guide (29)<br />
large washer (25) lower film guide (26]<br />
and a second large washer (25) over lower<br />
bearing protruding through sprocket guard<br />
plate (28). Note that the lower stud of<br />
the connecting link (60) must pass throug<br />
a hole in the left ear of the lower film<br />
guide. Spring (15) and lower loop form<br />
(14) are then installed on this stud an '<br />
secured with retaining ring (13). Leg.<br />
of spring (15) must be positioned to apply<br />
proper tension to lower loop form. Install<br />
large retaining ring (24). Fasten backup<br />
bracket (23) to sprocket guard plate.<br />
Attach auto-thread locking lever (21)<br />
and eccentric pivot (20) to casting with<br />
screw (19). Attach release spring (18)<br />
and bushing (17) to casting just above<br />
and to the left of lever (21)/ hooking<br />
long leg of spring behind the rear edg'<br />
of lever/ and handle assembly (8) and<br />
spring (9) with retaining ring (7). Install<br />
all rollers.