Bell & Howell - Projector - Filmosound 641 - 642 ... - Cine Information

More documents

Recommendations

Info

into it. This internal speaker is auto- Power Output matically disconnected when an external speaker is plugged into the output sockets. 15 watts (Speech and Music) 14 watt8 (Continuous Sine Wave) Controls Signal - Noise Ratio (Unweighted) Better than 65dB The photocell and microphone stages areprovided with separate volume controls. Frequency Response The Twin Tone controls provide means ——————————— of lifting or cutting bass and treble (Dependent on Tone Control Setting), independently. Mic. 50 - 10 Kc/s General Information Optical 5 0 - 7 Kc/s Sensitivity Mic. Socket Min. 8mV Max. 200mV. Mic. Socket Input Impedance - High. 47 Output Impedance to match 8 ohms or 16 ohms.
THE 16mm Filmosound Projector DESIGN 641 and 642 SERVICE INSTRUCTIONS SECTION 6 SPARE PARTS LISTS AND ILLUSTRATIONS All Orders for Spares must bear Model Number, Part Number and Description
Page 1 and 2: Disclaimer The information containe
Page 3 and 4: Model 642 Filmosound Projector (iii
Page 5 and 6: Section 3 Reassembly Procedure Page
Page 7 and 8: GENERAL INTRODUCTION This manual ha
Page 9 and 10: THE 16 mm Filmosound Projector DESI
Page 11 and 12: FAULT FINDING GUIDE 3. MISCELLANEOU
Page 13 and 14: FAULT FINDING GUIDE (Cont'd) TROUBL
Page 15 and 16: FAULT FINDING GUIDE (Cont'd) TROUBL
Page 19 and 20: 16. DISASSEMBLING SOUND HEAD 18. DI
Page 21 and 22: 16 mm Filmosound Projector DESIGN 6
Page 23 and 24: the bearing (28) and trigger (29) t
Page 25 and 26: the loop restorer shaft and below t
Page 27 and 28: enough to hold. Insert the spring (
Page 31 and 32: Insert the alignment rod (SER-550-2
Page 33 and 34: When adjusting Design 642 projector
Page 35 and 36: 48. REWIND CLUTCH ADJUSTMENTS (See
Page 37 and 38: 50. TIMING BELT IDLER ADJUSTMENT Be
Page 39 and 40: THE 16mm Filmosound Projector DESIG
Page 41 and 42: disconnected when an external speak
Page 43: will show that full power output is
Page 48 and 49: Figure 2. Fllmosound Projector Main
Page 50 and 51: Figure 3. Filmosound Projector Main
Page 52 and 53: Figure 4. Filmosound Projector Main
Page 54 and 55: Figure 5. Front Heel Arm Assembly
Page 56 and 57: o' / Figure 7. Projection Lampholde
Page 58 and 59: Figure 9. Sound Head Assembly I I i
Page 60 and 61: Figure 10. Mechanism Assembly (Shee
Page 63 and 64: Figure il MECHANISM ASSEMBLY. COMPL
Page 65 and 66: Figure il MECHANISM ASSEMBLY. COMPL
Page 67 and 68: Figure il MECHANISM ASSEMBLY, COMPL
Page 69 and 70: Figurs 14 LENS CARRIER ASSEMBLY Key
Page 71 and 72: Figure il SPROCKET GUARD ASSEMBLY K
Page 73 and 74: Figure il BLOWER ASSEMBLY Part No.
Page 75 and 76: I LL 1 2 3 4 5 6 7 8 9 10 1 1 12 13
Page 77 and 78: lOKn 3-9KP. Figure 21. Design 641 A
Page 79 and 80: 2 J 4 12 13 I H IS U ]7 18 19 20 21
Page 81 and 82: -a L-J *—5—fi 9 8 13 12 15 16 1
Page 83 and 84: Circuit Ref. Description R1 Resisto
Page 85: | Function Switch Pos»Tiof« I (
Page 89 and 90: JL ITC Wiring Diagram
Page 91 and 92: I Figure 26. 641 Amplifier - Circui
Page 93 and 94: ]Q - RJ3 R 26 CED 4 H R27 L C cp )
Page 95 and 96:
Model 644 Filmosound Projector 49
Page 97 and 98:
Filmosound 16 mm Projectors DESIGNS
Page 99 and 100:
MAGNETIC SOUND SYSTEM TROUBLES AND
Page 101 and 102:
GENERAL INSTRUCTIONS Carry out the
Page 103 and 104:
ADJUSTMENTS The following adjustmen
Page 105 and 106:
1 Hum bucking loop from head plug b
Page 107 and 108:
Filmosound 16 mm Projectors DESIGNS
Page 109 and 110:
The oscillator frequency is approx.
Page 111 and 112:
Figure 32 PROJECTOR MAIN PLATE (1)
Page 113 and 114:
Page 115 and 116:
Figure 33A PROJECTION LAMPHOLDER AS
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Figure 36 LENS CARRIER ASSEMBLY Key
Page 123 and 124:
Key No. 1 3A 3B 4A 10 % 10A @ 10B @
Page 125 and 126:
Figure 37 cont. 49 Switch, Magnetic
Page 127 and 128:
WAF^H tWirCH CONNECTION)! DESIGN 64
Page 129 and 130:
DESIGN 652 Filmosound 16 mm Project
Page 131 and 132:
Filmosound 16 mm Projector DESIGN 6
Page 133 and 134:
Page 135 and 136:
Figure K. Autoload System Adjustmen
Page 137 and 138:
Fig. L TIMING THE SPROCKETS
Page 139 and 140:
Fig.M. POSITIONING THE SOUND HEAD
Page 141 and 142:
Page 143 and 144:
AMPLIFIER PART NO.027097 Four fuses
Page 145 and 146:
Design 652 Figure 42 PROJECTOR MAIN
Page 147 and 148:
Design 652 Figure 43 SOUND HEAD ASS
Page 149 and 150:
Figure 44 652 MECHANISM ASSEMBLY CO
Page 151 and 152:
Figure 45 652 MECHANISM ASSEMBLY CO
Page 153 and 154:
652 MECHANISM ASSEMBLY COMPLETE con
Page 155 and 156:
Figure 46 Mechanism Assembly (3)
Page 157 and 158:
Figure 47. Aperture Plate Assembly
Page 159 and 160:
Figure 48, Lens Carrier Assembly
Page 161 and 162:
Figure 49 Sprocket Guard Assembly (
Page 163:
SYM: VALUE PACT MO 21 33o
show all

Bell & Howell - Projector - Filmosound 641 - 642 ... - Cine Information

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?