Sensor Installation Handbook Preface 3rd edition - Siemens ...

More documents

Recommendations

Info

Temperature · Frost protection 20 Temperature Frost protection · Air Leave a spare capillary loop of 20 cm so that functioning can be tested outside the unit. If the supply ductwork is outdoors or in an unheated space, then both the measuring head and the test loop of the thermostat must be located inside the duct and downstream of the heat exchanger. Install the capillary in the direction of air flow, downstream of the first water-filled heating coil exposed to frost. The capillary must be installed diagonal to the heat-exchanger pipes.
When installing on "drawer"-type units, ensure that the electrical connections are long enough to enable the units to be pulled out. If a water-filled cooling coil is installed upstream of the first heat exchanger, then the frost protection thermostat must be installed upstream of the cooling coil, in the direction of the air flow. With large heat exchangers, or with heat exchangers comprising several units, more than one frost thermostat must be installed (minimum 1 per unit). Temperature · Frost protection 21
Page 1: Sensor Installation Handbook Prefac
Page 5: Sensor Installation Handbook Prefac
Page 9 and 10: General notes for all sensors Alway
Page 11 and 12: Always allow a sufficient length of
Page 13 and 14: Temperature Immersion sensors · Wa
Page 15 and 16: Water-resistant seal Chilled water
Page 17 and 18: If the active length (a) of the sen
Page 19 and 20: Sensors mounted without immersion p
Page 21 and 22: Temperature Probe sensors · Air En
Page 23 and 24: The ambient temperature at the devi
Page 25 and 26: Temperature Averaging sensors Allow
Page 27: Do not bend the capillary too tight
Page 31 and 32: Use spacing clips to maintain a 50
Page 33 and 34: Do not install on external walls. A
Page 35 and 36: Temperature Outdoor sensors The sys
Page 37 and 38: Seal gaps between cable/plastic tub
Page 39 and 40: Temperature Surface-mounted strap-o
Page 41 and 42: Temperature Wind sensors Install on
Page 43 and 44: Avoid shade (from trees or neighbou
Page 45 and 46: A test hole must be provided for ev
Page 47 and 48: Distance for adiabatic humidificati
Page 49 and 50: Humidity sensor Average humidity me
Page 51 and 52: Seal gaps between cable/plastic tub
Page 53 and 54: Where there is a risk of condensati
Page 55 and 56: Avoid using tips which protrude int
Page 57 and 58: Where more than one sensor is used,
Page 59 and 60: Pressure Liquids Pressure tapping p
Page 61 and 62: Pressure measurement in conjunction
Page 63 and 64: Flow monitoring Water Correct insta
Page 65 and 66: Avoid recesses (e.g. shelving) and
Page 67 and 68: Floats: These are used in open and
Page 69 and 70: Principles of operation General All
Page 71 and 72: Example of response characteristic
Page 73 and 74: Stepless devices Stepless devices (
Page 75 and 76: Bimetal rod and tube Material Const
Page 77 and 78: Electrical resistance sensors Metal
Page 79 and 80:
Thermocouples These consist of two
Page 81 and 82:
Absolute humidity x g H 2O per kg o
Page 83 and 84:
Electronic systems Piezoelectric el
Page 85 and 86:
Measuring water velocity and flow L
Page 87 and 88:
Room temperature measurement Room s
Page 89 and 90:
Calibration of measuring sensors Th
Page 91 and 92:
Practical tips Frost protection the
Page 93 and 94:
Preventive frost protection thermos
Page 95 and 96:
Pressure control in VAV systems The
show all

Sensor Installation Handbook Preface 3rd edition - Siemens ...

Create successful ePaper yourself

Delete template?

Save as template?