Sensor Installation Handbook Preface 3rd edition - Siemens ...

More documents

Recommendations

Info

Air quality · Room 56 Air quality sensors Room sensors There are two types of air quality sensors: Mixed gas (or VOC) sensors The accumulation of up to 24 different gases is measured in the ambient air (total concentra - tion measured) Selective gas sensors These measure only one gas (e.g. CO 2) in the ambient air (selective measurement). Do not locate temperature or humidity sensors above or below the AQ sensor. The heated sensor element produces significant intrinsic heat in the device. Owing to this characteristic, the room temperature or room humidity must not be measured in the immediate vicinity. Maintain a clearance of minimum 60 mm on each side of the AQ sensor. CO2 sensors Selective gas sensors may require maintenance at regular intervals. Please consult the manufacturer’s instructions. The sensor must be installed in an accessible location.
Avoid recesses (e.g. shelving) and alcoves. Do not install directly adjacent to doors. Do not install behind curtains. Seal gaps between cable/plastic tubing and conduit. Otherwise measurements will be falsified by incorrect circulation of the air. Air quality · Room 57
Page 1:
Sensor Installation Handbook Prefac
Page 5:
Sensor Installation Handbook Prefac
Page 9 and 10:
General notes for all sensors Alway
Page 11 and 12:
Always allow a sufficient length of
Page 13 and 14: Temperature Immersion sensors · Wa
Page 15 and 16: Water-resistant seal Chilled water
Page 17 and 18: If the active length (a) of the sen
Page 19 and 20: Sensors mounted without immersion p
Page 21 and 22: Temperature Probe sensors · Air En
Page 23 and 24: The ambient temperature at the devi
Page 25 and 26: Temperature Averaging sensors Allow
Page 27 and 28: Do not bend the capillary too tight
Page 29 and 30: When installing on "drawer"-type un
Page 31 and 32: Use spacing clips to maintain a 50
Page 33 and 34: Do not install on external walls. A
Page 35 and 36: Temperature Outdoor sensors The sys
Page 37 and 38: Seal gaps between cable/plastic tub
Page 39 and 40: Temperature Surface-mounted strap-o
Page 41 and 42: Temperature Wind sensors Install on
Page 43 and 44: Avoid shade (from trees or neighbou
Page 45 and 46: A test hole must be provided for ev
Page 47 and 48: Distance for adiabatic humidificati
Page 49 and 50: Humidity sensor Average humidity me
Page 51 and 52: Seal gaps between cable/plastic tub
Page 53 and 54: Where there is a risk of condensati
Page 55 and 56: Avoid using tips which protrude int
Page 57 and 58: Where more than one sensor is used,
Page 59 and 60: Pressure Liquids Pressure tapping p
Page 61 and 62: Pressure measurement in conjunction
Page 63: Flow monitoring Water Correct insta
Page 67 and 68: Floats: These are used in open and
Page 69 and 70: Principles of operation General All
Page 71 and 72: Example of response characteristic
Page 73 and 74: Stepless devices Stepless devices (
Page 75 and 76: Bimetal rod and tube Material Const
Page 77 and 78: Electrical resistance sensors Metal
Page 79 and 80: Thermocouples These consist of two
Page 81 and 82: Absolute humidity x g H 2O per kg o
Page 83 and 84: Electronic systems Piezoelectric el
Page 85 and 86: Measuring water velocity and flow L
Page 87 and 88: Room temperature measurement Room s
Page 89 and 90: Calibration of measuring sensors Th
Page 91 and 92: Practical tips Frost protection the
Page 93 and 94: Preventive frost protection thermos
Page 95 and 96: Pressure control in VAV systems The
show all

Sensor Installation Handbook Preface 3rd edition - Siemens ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?