Serie UTBS - Soler & Palau Sistemas de VentilaciÃ³n, SLU

More documents

Recommendations

Info

9.5.2. REPLACING FILTERS FOR IN-LINE RECOVERY MODULES To remove the filter, open the inspection door by pulling it out. Turn the handle and remove the filter. ENGLISH 9.6. COILS If you detect any problem in the coils and they need to be removed, loosen the bolts from the panel where they are located, remove the panel and extract the coils. The coils are installed in slod for easy slide in and slide out. 9.7. DAMPERS • Make sure that the damper can open and close unrestrictedly and the (way) is unobstructed. • For manually controlled dampers fix the handle firmly to prevent the damper close while the unit is running. 64
9.8. SILENCERS • To remove the baffles unscrew the corresponding side panel. ENGLISH 9.8.1. MIXING MODULE • Air 2 inlet section: Is sent with a fixed position of the dampers. If not coincide with the needs of the installation, change the frontal panel as shown. • Air 3 inlet section (A+B): When it is installed between two modules will have to remove the front panels as shown. (B) A B remove panel remove panel 65
Page 1 and 2:
Serie UTBS Unidades de tratamiento
Page 3 and 4:
1. Generalidades • Le agradecemos
Page 5 and 6:
5. MANIPULACIÓN • A la recepció
Page 7 and 8:
ESPAÑOL Modelo A (mm) B (mm) UTBS-
Page 9 and 10:
6.5.2. ENSAMBLAJE DE JUNTAS FLEXIBL
Page 11 and 12:
6.6.1. CONEXIÓN DE LOS MOTORES ESP
Page 13 and 14: Conexionado electrico BE-3 24 kw 1
Page 15 and 16: Conexionado electrico BE-8 22,5 kw
Page 17 and 18: ESPAÑOL • Comprobar que el inter
Page 19 and 20: Funcionamiento a presión constante
Page 21 and 22: • Ajustar el rango de caudal y el
Page 23 and 24: Pasos a seguir en caso de fallo del
Page 25 and 26: 6.8. CONEXIÓN DEL EQUIPO A LA RED
Page 27 and 28: MUY IMPORTANTE: • El proceso de f
Page 29 and 30: Estos extintores deben ser adecuado
Page 31 and 32: 9.5.2. SUSTITUCIÓN DE FILTROS EN R
Page 33 and 34: 9.8.2. CAJA DE MEZCLA 2 VÍAS CON B
Page 35 and 36: ENGLISH TABLE OF CONTENTS 1. OVERVI
Page 37 and 38: 4. UNIT LABELING • The unit comes
Page 39 and 40: 6.3. INSTALLATION SITE • Avoid in
Page 41 and 42: 6.5. ASSEMBLING THE MODULES The mod
Page 43 and 44: 6.6. ELECTRICAL CONNECTION • Befo
Page 45 and 46: The attached schematic shows how to
Page 47 and 48: Conexionado Wiring electrico diagra
Page 49 and 50: 6.7. CONNECTING THE PRESSURE SENSOR
Page 51 and 52: CONSTANT PRESSURE CONTROL Leave one
Page 53 and 54: Constant pressure operation • Che
Page 55 and 56: Firstly, enter programming mode. Th
Page 57 and 58: Menu Parameter Value drC SFr 8 kHz
Page 59 and 60: • We suggest having all the eleme
Page 61 and 62: • Turn on the external main power
Page 63: 9.4. FANS • Every three months, c
Page 67 and 68: WARNING!!! Support the heat exchang
Page 69 and 70: 1. GÉNÉRALITÉS • Ce produit a
Page 71 and 72: 5. MANIPULATION • Dès la récept
Page 73 and 74: Modèle A (mm.) B (mm.) UTBS-2 750
Page 75 and 76: 6.5.3. ASSEMBLAGE D’APPAREILS EN
Page 77 and 78: • Enlever le couvercle de la boit
Page 79 and 80: BATTERIE ÉLECTRIQUE À 2 ÉTAGES (
Page 81 and 82: 6.8. RACCORDEMENT DE L’UNITE DE T
Page 83 and 84: PREPARATION HUMIDIFCATEUR TRÈS IMP
Page 85 and 86: 9.1. BATTERIES D’ÉCHANGE THERMIQ
Page 87 and 88: 9.6. BATTERIES Pour extraire les ba
Page 89 and 90: 10. RECYCLAGE La norme de la CE et
show all

Serie UTBS - Soler & Palau Sistemas de VentilaciÃ³n, SLU

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?