Altivar 71 â Guide de programmation - Skills Canada
Altivar 71 â Guide de programmation - Skills Canada
Altivar 71 â Guide de programmation - Skills Canada
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
[1.7 FONCTIONS D’APPLI.] (FUn-)<br />
NNC-<br />
Co<strong>de</strong> Nom / Description Plage <strong>de</strong> réglage Réglage usine<br />
b [MULTIMOTEURS/CONF]<br />
CHN<br />
CnF1<br />
nO<br />
YES<br />
nO<br />
LI1<br />
-<br />
-<br />
C111<br />
-<br />
-<br />
-<br />
CnF2<br />
nO<br />
LI1<br />
-<br />
-<br />
C111<br />
-<br />
-<br />
-<br />
M [Multimoteurs]<br />
v [Non] (nO) : Multiconfigurations possible.<br />
v [Oui] (YES) : Multimoteurs possible<br />
M [2 configurations]<br />
v [Non] (nO) : Pas <strong>de</strong> commutation.<br />
v [LI1] (LI1) à [LI6] (LI6)<br />
v [LI7] (LI7) à [LI10] (LI10) : si carte entrées/sorties logiques VW3A3201 présente<br />
v [LI11] (LI11) à [LI14] (LI14) : si carte entrées/sorties étendues VW3A3202 présente<br />
v [C111] (C111) à [C115] (C115) : avec Modbus intégré<br />
v [C211] (C211) à [C215] (C215) : avec CANopen intégré<br />
v [C311] (C311) à [C315] (C315) : avec une carte <strong>de</strong> communication<br />
v [C411] (C411) à [C415] (C415) : avec une carte Controller Insi<strong>de</strong><br />
Commutation 2 moteurs ou 2 configurations.<br />
M [3 configurations]<br />
v [Non] (nO) : Pas <strong>de</strong> commutation.<br />
v [LI1] (LI1) à [LI6] (LI6)<br />
v [LI7] (LI7) à [LI10] (LI10) : si carte entrées/sorties logiques VW3A3201 présente<br />
v [LI11] (LI11) à [LI14] (LI14) : si carte entrées/sorties étendues VW3A3202 présente<br />
v [C111] (C111) à [C115] (C115) : avec Modbus intégré<br />
v [C211] (C211) à [C215] (C215) : avec CANopen intégré<br />
v [C311] (C311) à [C315] (C315) : avec une carte <strong>de</strong> communication<br />
v [C411] (C411) à [C415] (C415) : avec une carte Controller Insi<strong>de</strong><br />
[Non] (nO)<br />
[Non] (nO)<br />
[Non] (nO)<br />
Commutation 3 moteurs ou 3 configurations.<br />
tnL-<br />
tUL<br />
nO<br />
LI1<br />
-<br />
-<br />
-<br />
Nota : Pour obtenir 3 moteurs ou 3 configurations [2 configurations] (CnF1) doit aussi être configuré.<br />
b [AUTO-REGLAGE PAR LI]<br />
M [Affect. auto-réglage]<br />
v [Non] (nO) : Non affecté<br />
v [LI1] (LI1)<br />
:<br />
:<br />
v [...] (...) : Voir conditions d’affectation page 112.<br />
L’auto-réglage est effectué lorsque l’entrée ou le bit affecté passe à 1.<br />
[Non] (nO)<br />
Nota : L’auto-réglage entraîne la mise sous tension du moteur.<br />
185