Montage- und Gebrauchsanleitung Universal Anschlagpunkt 115

Weitere Magazine

Empfehlungen

Info

5. Fitting the universal anchorage point 5.3 Fitting to a fixed vertical ladder IMPORTANT: The operating licence will be revoked and all warranties on the part of manufacturer invalidated if this device is not handled in accordance with these instructions (i.e. improper assembly or fitting, surface damage, etc.). The universal anchorage point is approved for fi tting to Hailo aluminium vertical ladders, type ALO 72 MA/BA. When fi tting to ladders supplied by other manufacturers, the designer must verify that the required stability is available for absorbing the forces generated in the event of a fall. The ladder must be designed and installed to meet EN ISO 14122-4 requirements. The universal anchorage point is fi tted to 5 ladder rungs with various fi xtures. 1) 3 ladder rungs are fi rst reinforced using a rung repair kit [1]. Push a tube [1a] into each rung and secure it on both sides with an adjusting screw [1c] and countersunk screw M16x50 [1b]. Torque to be applied to screws: 80 Nm 2) Secure the U profi le [2] to the 1st and 5th rungs of the ladder from behind using the U bolt set [5]. Torque: 20 Nm 3) Secure the location plate [3] to the 3 middle rungs from the front using the U bolt set [5]. Torque: 20 Nm 4) Fit the anchorage point [4] to the location plate (M16x50 bolts, DIN 933, property class 8.8 [6]). Torque: 210 Nm The position of the location plate on the ladder can be varied. The anchorage point can be fi tted in the centre or on the side of the ladder. Ensure that the specifi ed tread widths are observed. Attached on the side: X = min. 300 mm Attached in the centre: X = min. 150 mm When carrying out the annual inspection of the anchorage point, the bolts and screws must be checked to ensure that they are screwed tight. 30 Instructions for fitting and use • <strong>Universal</strong> anchorage point • Revised 2013-11/GB/02
GB Instructions for fitting and use • <strong>Universal</strong> anchorage point • Revised 2013-11/GB/02 31
Seite 1 und 2: Hailo Wind Systems Hailo Universal
Seite 3 und 4: Inhaltsverzeichnis: 1. Bestimmungsg
Seite 5 und 6: • Der Universal Anschlagpunkt dar
Seite 7 und 8: 4. Kennzeichnung Typenschild A: Uni
Seite 9 und 10: 5.2 Montage an Bauwerk Montage an M
Seite 11 und 12: DE Montage- und Gebrauchsanleitung
Seite 17 und 18: 8. Rettungsmaßnahmen Der Unternehm
Seite 19 und 20: 1. Prüfung in Ordnung nicht in Ord
Seite 21 und 22: Notes Instructions for fitting and
Seite 23 und 24: Table of contents: 1. Approved use
Seite 25 und 26: • The universal anchorage point i
Seite 27 und 28: 4. Markings Type plate A: Universal
Seite 29: 5.2 Fitting to the structure Fittin
Seite 33 und 34: GB Instructions for fitting and use
Seite 35 und 36: GB Instructions for fitting and use
Seite 37 und 38: 8. Rescue measures Information on F
Seite 39 und 40: Inspection 1 Inspection 2 Inspectio

Montage- und Gebrauchsanleitung Universal Anschlagpunkt 115

Erfolgreiche ePaper selbst erstellen

Template löschen?

Als Template speichern?