Bedienungsanleitung - Gustav Klauke GmbH

Weitere Magazine

Empfehlungen

Info

1.2 Initializing In industrial plants strong electromagnetic interferences acceeding the values published in the EN 50081 and EN 50082, may distort resp. disturb results in digital electronic devices. This becomes apparent when unlikely measuring data is generated or when the unit does not reakt on any input. In this case you have the possibility to set the unit on the initial pre-set default parameters. However all your parameters you fed in before such as calibration value, measuring units, current output of the pressure sensors and force sensors will then be deleted. To return to the default parameter actuate the following keys: Initialization Version 2.1 p and F and The input has to be made within 3 seconds. Afterwards you can choose German, English or French as operation language. This will be done with the key which now has the effect SPRACHE / LANGUAGE Deutsch of an arrow head key. Prog The choice is to be confirmed with the key . ENT english francais * * * * * UNIT * * * * SI US With the which has now the effect of an arrow head key a allows you to change from Sl- to the US-measuring units. Prog Confirm the choice with the key . ENT Sl-units are e.g. bar, kN etc. When switching over to US-measuring units the common scales are e.g. psi or am. to. 1.3 Date input and time The next menu for the data input is immediately called. * * * Date input * * * * * Day : 01 Month : 06 Year : 1999 The input is done by means of the two keys for the input of the figures and selection command of the next decimal place. * * * Time input * * * * * hours : 13 minutes : 55 Please observe that each line after the input of the figures is finished by pressing the key Prog ENT ; only then a jump to the next line follows. -32-
INIT? 20.05.99 PROG->Yes The call for initializing comes automatically. Here you can decide whether you want to initialize or not. TP 200 p p ^ 0.0 bar 0.0 bar If you don’t want any initializing, press any key except for „Prog/Ent“, and the indication of measured values appears automatically. If you however want an initialisation, press the key Prog ENT , and all your data fed before like calibration value, measuring units are erased. INIT? 20.05.99 PROG->Yes After this the appliance jumps back straight to the indication of measured values. INIT? Prog ENT After an initializing the default settings stated in the following example are valid: TF 70 F F ^ 61.8 kN 65.7 kN Force-sensing F Force measuring range preadjusted on 0 to 70 kN Measuring units in Sl Language German -33-
Seite 1 und 2: Bedienungsanleitung für TC 1 TF 70
Seite 3 und 4: Inhaltsverzeichnis Allgemeines ....
Seite 5 und 6: Hinweise zum richtigen Laden des in
Seite 7 und 8: 1. Bedienung TC 1 Über das LCD-Dis
Seite 9 und 10: INIT? 20.05.99 TP 200 p p ^ PROG->J
Seite 11 und 12: 2.3 Nullpunktkorrektur * Nullpunktk
Seite 13 und 14: 2.5 Kraft- bzw. Druckmessung Kraftm
Seite 15 und 16: 3.4 Darstellung aller einzelnen ges
Seite 17 und 18: * * * * * * PROG * * * * * * * Es e
Seite 19 und 20: 5.8 Auswahl Tabelle TF 70 F F ^ 61.
Seite 21 und 22: 7. Anschlußbelegungen des TC 1 -21
Seite 23 und 24: 9. Fehlersuche Das Klauke TC 1 wurd
Seite 25 und 26: Operating instructions for TC 1 TF
Seite 27 und 28: Index General .....................
Seite 29 und 30: Notes on proper charging of the int
Seite 31: 1. Operation of TC 1 The LCD-displa
Seite 35 und 36: 2.3 Zero point correction * Zero po
Seite 37 und 38: 2.5 Force- resp. pressure measuring
Seite 39 und 40: 3.4 Picturing of all single, stored
Seite 41 und 42: * * * * * * PROG * * * * * * * At s
Seite 43 und 44: 5.8 Choice of schedule TF 70 F F ^
Seite 45 und 46: 7. Pin configurations of the TC 1 -
Seite 47 und 48: 9. Fault finding The TC 1 was check

Bedienungsanleitung - Gustav Klauke GmbH

Erfolgreiche ePaper selbst erstellen

Template löschen?

Als Template speichern?