Bedienungsanleitung - Gustav Klauke GmbH

Weitere Magazine

Empfehlungen

Info

5.6 Choice of manual scaling * * Scaling * * manual PROG-> Confirm When invoking the measuring value „scaling“ the measuring range resp. margin of the measuring range of the selected sensor and the number of the measuring cycles are always preadjusted. 5.7 Individual scaling Scaling F kN *Minimum value: 0 Maximum value: 70 Scaling F kN *Minimum value: 1 2 Maximum value: 6 8 In our example for a force sensor F = 70 kN the lower measuring value (minimum value) is preset with 0, and the final value of the measuring range (maximum value) is preset with 70. Both of these preset values can be changed individually by the user. In the next example the modification of a scaling for the force sensor F is being represented. The star symbol shows the active input for the minimum value. In order to reach the numerical input you have to press the key . Doing this please observe the sparkling cursor below the figure which is to be fed in. The modification of the input of the figures is made over the key . Scaling x *Minimum value: 0001 The input of the figures takes place as already described on page 11, Maximum value: 0008 pararaph 2.3. Prog After the input the key is to be pressed. ENT * * * * Printing * * * * HP colour When the individual scaling F is finished, the point of menu „scaling x“ is invoked automatic-ally. Here the user can choose his working cycles as stored peak values in the storage area of 1 to 500. In our example the measuring cycles between 1 to 8 (operating cycles) were chosen for the logging. The element of the curve cycle is represented in the limits of the measuring range between 12 kN up to a maximum of 68 kN with 8 measuring cycles according to the choice of the user resp. is printed. By pressing the key Prog ENT the printer is started. * * * * Printing * * * * HP colour 28% 100% The type of printer HP colour chosen before in our example is indicated at short notice; after this the following indication appears notifying the percentage rate of what has already been printed out. When reaching 100 %, the measured value indication is invoked automatically. TF 70 F F ^ 61.8 kN 65.7 kN A printout can be stopped at all times with the key Clear . -42-
5.8 Choice of schedule TF 70 F F ^ 61.8 kN 65.7 kN If a printout of table work is desired instead of a graphical chart, the menu „printer“ is reached out of the known measured value indication Prog by pressing the two keys and Output . ENT * * Menu Printer * * * Printout Choice of printer With the key the choice „printout“ is invoked – observe the star symbol – and the menu „type of print“ appears automatically. The table is chosen over the key please observe star symbol. With the key Prog ENT Prog ENT the choice of table is confirmed. * * Type of printout * * Graphic PROG-> Confirm The menu of the routine „printing“ appears automatically which is activated by a further pressing of the key Prog ENT , and all stored * * Type of printout * * measured values are printed out in a number column with mean values and standard deviations. * chart PROG-> Confirm * * Printing * * HP colour PROG-> Confirm -43-
Seite 1 und 2: Bedienungsanleitung für TC 1 TF 70
Seite 3 und 4: Inhaltsverzeichnis Allgemeines ....
Seite 5 und 6: Hinweise zum richtigen Laden des in
Seite 7 und 8: 1. Bedienung TC 1 Über das LCD-Dis
Seite 9 und 10: INIT? 20.05.99 TP 200 p p ^ PROG->J
Seite 11 und 12: 2.3 Nullpunktkorrektur * Nullpunktk
Seite 13 und 14: 2.5 Kraft- bzw. Druckmessung Kraftm
Seite 15 und 16: 3.4 Darstellung aller einzelnen ges
Seite 17 und 18: * * * * * * PROG * * * * * * * Es e
Seite 19 und 20: 5.8 Auswahl Tabelle TF 70 F F ^ 61.
Seite 21 und 22: 7. Anschlußbelegungen des TC 1 -21
Seite 23 und 24: 9. Fehlersuche Das Klauke TC 1 wurd
Seite 25 und 26: Operating instructions for TC 1 TF
Seite 27 und 28: Index General .....................
Seite 29 und 30: Notes on proper charging of the int
Seite 31 und 32: 1. Operation of TC 1 The LCD-displa
Seite 33 und 34: INIT? 20.05.99 PROG->Yes The call f
Seite 35 und 36: 2.3 Zero point correction * Zero po
Seite 37 und 38: 2.5 Force- resp. pressure measuring
Seite 39 und 40: 3.4 Picturing of all single, stored
Seite 41: * * * * * * PROG * * * * * * * At s
Seite 45 und 46: 7. Pin configurations of the TC 1 -
Seite 47 und 48: 9. Fault finding The TC 1 was check

Bedienungsanleitung - Gustav Klauke GmbH

Erfolgreiche ePaper selbst erstellen

Template löschen?

Als Template speichern?