Manual - Tracker
Manual - Tracker
Manual - Tracker
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
How to use the <strong>Tracker</strong> Hunter® 3.0 to the fullest<br />
A-GPS<br />
A-GPS is supported only with <strong>Tracker</strong> TTA-310ia and <strong>Tracker</strong> G400 collars.<br />
A-GPS is system where the collar uploads orbital data information from satellites through GPRS network. This<br />
makes positioning of the device faster and more stabile. As a default, A-GPS is on. When the collar is added to<br />
the <strong>Tracker</strong> Live service, it will automatically receive a command to update A-GPS if expiring.<br />
A-GPS modes can be set in Configuration commands menu, which can be found in Targets > All targets > Dogs ><br />
(name of the target) > Configuration commands.<br />
There are several A-GPS modes available in G400 that you can choose from.<br />
A-GPS Off: A-GPS is not available.<br />
A-GPS Update once: A-GPS data is downloaded just once (After download, information is valid for approx. four<br />
days).<br />
A-GPS Update when switching on: A-GPS data is downloaded automatically when the device is switched on.<br />
A-GPS Update if expiring: Recommended mode for new G400 collars which use <strong>Tracker</strong> Live service. A-GPS<br />
data for two following days is downloaded every day (a day before the previous information is expiring), so you will<br />
always have relevant A-GPS data available.<br />
A-GPS Update when needed: Recommended mode when the collar is only located via SMS and no GPRS data<br />
package is obtained. A-GPS data is downloaded only when needed (A-GPS data has expired and the amount of<br />
satellites available decreases to less than 4). This is the most cost-effective mode.<br />
TIPS!<br />
A-GPS data is transferred through GPRS network. The size of the data packet is approx. 0,01 MB per day. You<br />
will receive SMS messages of all A-GPS activities. The message contains information about the status of<br />
download, success rate and the expiration time of the data.<br />
GPS / GSM modes and power settings<br />
Power consumption of the phone:<br />
GPS consumes a lot of power. If you want to reduce it, you have two options. In the Menu > Settings you can<br />
either choose how often My position is updated (go to Location) or you can also deactivate GPS (GPS) . In this<br />
case when you need position, you can choose My position as displayed target and go to Targets > Locate (GPS<br />
will turn on, update the position and the turn off again)<br />
Power consumption of the device:<br />
GPS modes affect the GPS sensitivity, response time and power consumption of the device. Power consumption<br />
modes of the device can be changed when the dog is out of sight as long as it is within the GSM network.<br />
GPS modes are adjusted from Configuration commands menu which can be found in Targets > List all > Dogs ><br />
(name of the target )> Configuration commands.<br />
Off (turns on automatically when position is needed) mode (GPS is Off but is turned on when the user<br />
acquires position data or according to the settings of Geofence) consumes very little power, but the r esponse time<br />
increases. Also, when not using A-GPS, the device may have difficulty acquiring position data.<br />
Power Save mode (GPS acquires position as powerfully as in Full Power, but automatically reduces the power<br />
when GPS signal strength is good) provides a good performance with less power consumption.<br />
Full mode (GPS acquires position as powerfully as possible) should be used mainly when the device has trouble<br />
acquiring position. In this mode the device consumes the most power.<br />
GSM and GPS Off mode (both GSM and GPS are Off) means, that the device can not be contacted. However,<br />
GSM module of the device is automatically turned on periodically (every 30 minutes during the day and 60<br />
minutes during the night – values can be adjusted by <strong>Tracker</strong> customer support). This mode provides very low<br />
power consumption.<br />
To use this power mode it is recommended to stop all Live trackings and set SMS tracking or Area alarm on for<br />
e.g. every 30 minutes or less. If you request tracking more frequently than 15 minutes, the device stays on all<br />
times and this mode does not save any more power than GPS Off state does.<br />
Automatic mode adjusts the mode according to the status of the battery. When battery is 70 % or more, the<br />
device is in the Power Save mode. When battery is 40 to 70 %, the device is in GPS Off mode. Under 40 %, the<br />
device is in GSM and GPS Off mode. (The values of Automatic mode can be adjusted by <strong>Tracker</strong> customer<br />
support the same way as adjustments can be done in the GSM and GPS Off mode).<br />
NOTE!<br />
Settings vary according to the collar. These are the features of <strong>Tracker</strong> G400.<br />
46