Freedom 2100 Motor Control Center Installation and - Eaton Canada

Instruction Booklet IM04302004E
Effective October 2010
Manual/automatic Reset
The overload relay is factory set at “M” for manual reset operation
as shown in the illustration . For automatic reset operation, turn the
reset adjustment dial to the “A” position . Automatic reset is not
intended for two-wire control devices .
RESET
ADJUSTMENT
DIAL
18
Example of
setting for
manual reset .
Test for Trip Indication
To test overload relay for trip indication when in manual reset, pull
out the blue Reset button . An orange flag will appear indicating that
the device has tripped . Push Reset button in to reset .
For more information, go to www .1800oldunit .com or call
1-800-OLD-UNIT .
Table 1. NEMA Size 0 and 1 Heater Pack Selection Table
Motor FLa rating
FLa Dial positions
A B C D
0.254
0.375
0.560
0.814
1.20
1.79
2.15
3.23
4.55
6.75
9.14
14.0
18.7
23.5
0.306
0.452
0.676
0.983
1.45
2.16
2.60
3.90
5.50
8.17
10.8
16.9
22.7
28.5
0.359
0.530
0.791
1.15
1.71
2.53
3.04
4.56
6.45
9.58
12.4
19.9
26.7
33.5
0.411
0.607
0.907
1.32
1.96
2.90
3.49
5.23
7.40
11.0
14.0
22.8
30.7
—
eaton Corporation www.eaton.com
Size F
Standard
trip
Class 20
H2001B
H2002B
H2003B
H2004B
H2005B
H2006B
H2007B
H2008B
H2009B
H2010B
H2011B
H2012B
H2013B a
H2014B a
a After the above referenced settings have been made, rotate the FLA dial one position clockwise for
these heaters (see table). If less than one position is available, rotate dial maximum. This does not
apply when these heaters are used with adapter base. Catalog No. C306TB1. Exception: does not
apply to AN16DN0.
Notee: For maximum ratings, see table below . Use 75°C copper conductors
only . Maximum wire size—8 AWG .
neMa Size amperes Size amperes
0 18 — —
1 27 F 32
warning
to provide Continued proteCtion againSt fire or SHoCk Hazard,
tHe CoMplete overload relay MuSt be replaCed if burnout of
tHe Heater eleMent oCCurS.
M
A
Freedom 2100 Motor Control Center
Installation and Maintenance Manual
Table 2. NEMA Size 2 Heater Pack Selection Table
Motor FLa rating a
FLa Dial positions
a B C D
Size J and K
Standard trip
Class 20
3.23
4.55
6.75
9.14
14.0
18.7
23.5
29.0
39.6
53.9
3.90
5.50
8.17
10.8
16.9
22.7
28.5
34.0
45.5
60.9
4.56
6.45
9.58
12.4
19.9
26.7
33.5
39.1
51.5
67.9
5.23
7.40
11.0
14.0
22.8
30.7
38.5
44.1
57.4
74.9
H2008B
H2009B
H2010B
H2011B
H2012B
H2013B
H2014B
H2015B
H2016B b
H2017B b
a For motor FLA values not listed, turn the dial clockwise for higher or counterclockwise for lower
ratings.
b After the above reference settings have been made, rotate the FLA dial one position clockwise for
these heaters (see table). If less than one position is available, rotate dial to maximum. This note
does not apply when these heaters are used with adapter base. Catalog No. C306TB1.
Notee: For maximum ratings, see table below . Use 167ºF (75°C) copper
conductors only . Maximum wire size—3 AWG .
neMa Size amperes Size amperes
2 45 J 60
— — K 73
Table 3. NEMA Size 3 and 4 Heater Pack Selection Table
Motor FLa rating a
FLa Dial positions
A B C D
Size n
Standard trip
Class 20
18.0
24.6
33.5
45.7
62.2
84.7
106.0
20.2
27.6
37.5
51.2
69.7
94.9
118.0
22.3
30.5
41.5
56.7
77.1
105.0
131.0
24.5
33.4
45.6
62.1
84.6
115.0
144.0
H2018
H2019
H2020
H2021
H2022
H2023
H2024
a For motor FLA values not listed, turn the dial clockwise for higher or counterclockwise for
lower ratings.
Notee: For maximum ratings, see table below . Minimum wire size—6 AWG .
neMa Size amperes Size amperes
3 90 N 14
4 135 — —