Download - Brunswick

More documents

Recommendations

Info

16 Video Pinsensing System Note: If you change the Use Respot Solenoid option you must update the VPS by selection menu option Update VPS Configuration. Enter Take Data Delay Time - Select this option to enter the time delay from ball detect to take data. This option is only used on machines that do not have take data switches. Note: If you change the Take Data Delay Time you must update the VPS by selection menu option Update VPS Configuration. Read Pinsetter Cycles - Select this option to display the number of pinsetter cycles that have occurred since cycle count was cleared. Once selected you will be prompted to select either the Left Lane or Right Lane. The count for the select lane can be set to 0 by selecting the clear option on the display. Engage NPS - Select this option to energize the New Pin Solenoid. Once selected you will be prompted to select either the Left Lane or Right Lane. Calibrating the VPS To calibrate the VPS, Perform the following procedure: 1. Turn on both pinsetters. Make sure that both pin lights are on. 2. Cycle both machines so that there are 10 pins on the pindeck for each lane. 3. Make sure that the masking unit is lowered to the normal “bowling” position. 4. Momentarily press the calibration pushbutton swtich for the lane needing calibration. Wait until the image LED begins flashing and the calibration LED is lit before continuing to next step. 5. Repeat step 4 for the other calibration switch if calibration of both lanes is desired. 6. Bowl on the lane pair to verify proper scoring. Note: Step 4 can also be performed using the scorer maintenace menu selection titled “Start Calibration”
Ball Detect Figure 8. VPS Ball Detector The VPS uses a ball detector that is an infrared sensing device. The ball detector unit is made up of two infrared transmitters and receivers, one for each lane. Within each lane unit there are two lenses, one to focus the transmitted infrared beam toward the retroreflector on the opposite side of the lane, and one to focus the return light from the reflector onto the infrared receiver. A red indicator LED turns off when the infrared beam is blocked. Refer to Figure 8. (1) ADJUSTMENT SCREWS (2) RED LED INDICATOR (3) LENS (4) KICKBACKS Video Pinsensing System 17
Page 1 and 2: Contents General Description ......
Page 3 and 4: General Description Figure 1. VPS C
Page 5 and 6: VPS Chassis Figure 3. Rear of VPS C
Page 7 and 8: Logic PCB (2) EVEN CAMERA (3) ODD C
Page 9 and 10: I/O PCB (16) RIGHT LANE CALIBRATION
Page 11 and 12: (5) Stat LED - These green LEDs fla
Page 13 and 14: VPS Camera The VPS uses two cameras
Page 15: Download Menu - Select this option
Page 19 and 20: Brunswick A-2 Pinsetter Modificatio
Page 21 and 22: Figure 12. 44 o /144 o Switch Adjus
Page 23 and 24: In order to make the New Pins Solen
Page 25 and 26: (1) STRIKE SELECTOR Link Raised. Fi
Page 27 and 28: Brunswick A-2 Pinsetter Scoring Seq
Page 29 and 30: Figure 19. First Ball Foul - Brunsw
Page 31 and 32: Figure 21. No Tap - Brunswick A-2 N
Page 33 and 34: AMF Pinspotter Scoring Sequence of
Page 35 and 36: 3rd Ball 10th Frame All Models The
Page 37 and 38: Figure 24. VPS AMF Pinspotters (1)
Page 39 and 40: Figure 27. 57-300662-000 VPS Power
Page 41 and 42: Figure 32. 57-300668-000. Ball Dete
Page 43 and 44: Figure 36. 57-300854-000 Manager’
Page 45: TL1 TS1 19 G H F E D C B A BLUE ORA

Download - Brunswick

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?