An Installation Pocket Reference Guide.pdf - Anixter

More documents

Recommendations

Info

3. Twisted-Pair Cable| STEP-BY-STEP – TWISTED-PAIR CABLE PREPARATION AND CONNECTOR TERMINATION The following steps will guide you through the preparation and termination process for UTP cable. Following these guidelines will help give you the optimum performance from the twisted-pair cabling. Step 1: The tools you will need: • Jacket stripper • Punch-down tool (not shown) • Wire cutters (not shown) Step 2: Insert cable into stripping tool to the desired strip length. Strip off only as much cable jacket needed to properly terminate the pairs (1 to 1½ inches should be sufficient to terminate pairs). anixter.com 31|
|3. Twisted-Pair Cable Step 3: Holding the cable near the tool, rotate the tool around the cable several times. Step 4: Slightly bend the outer jacket and manually remove the cut piece or slide the cut outer jacket with the stripper. Step 5: Bend each pair in one direction to expose the rip cord, binder or cross-web filler on the cable. |32 1.800.ANIXTER
Page 1 and 2: Products. Technology. Services. Del
Page 3 and 4: TABLE OF CONTENTS Table of Contents
Page 5 and 6: INTRODUCTION Introduction| Anixter:
Page 7 and 8: |1. Standards Reference Documents S
Page 9 and 10: |1. Standards Reference Documents A
Page 11 and 12: 2. BUILDING SUBSYSTEMS 2. Building
Page 13 and 14: 2. Building Subsystems| 1. Entrance
Page 15 and 16: Table 2.1 - Work Area Components Eq
Page 17 and 18: Application Parameter Nominal Wavel
Page 19 and 20: Star Wiring 2. Building Subsystems|
Page 21 and 22: |3. Twisted-Pair Cable SECTION 3: T
Page 23 and 24: |3. Twisted-Pair Cable Table 3.1 -
Page 25 and 26: |3. Twisted-Pair Cable Anixter’s
Page 27 and 28: |3. Twisted-Pair Cable Twisted-Pair
Page 29: |3. Twisted-Pair Cable Testing Veri
Page 33 and 34: |3. Twisted-Pair Cable Step 8: Pres
Page 35 and 36: |3. Twisted-Pair Cable Step 12: Pla
Page 37 and 38: |4. Coaxial Cable SECTION 4: COAXIA
Page 39 and 40: |4. Coaxial Cable Table 4.3 - Coaxi
Page 41 and 42: |4. Coaxial Cable F Connector • T
Page 43 and 44: |4. Coaxial Cable Step 3: Holding t
Page 45 and 46: |4. Coaxial Cable Step 7: Inspect t
Page 47 and 48: |5. Fiber Optic Cables SECTION 5: F
Page 49 and 50: |5. Fiber Optic Cables Figure 5.5 -
Page 51 and 52: |5. Fiber Optic Cables Attachment M
Page 53 and 54: |5. Fiber Optic Cables Testing Figu
Page 55 and 56: |5. Fiber Optic Cables Step 2: Meas
Page 57 and 58: |5. Fiber Optic Cables Step 7: Care
Page 59 and 60: |5. Fiber Optic Cables Step 11: Slo
Page 61 and 62: |5. Fiber Optic Cables Step 16: Mak
Page 63 and 64: |5. Fiber Optic Cables Step 20: Clo
Page 65 and 66: |5. Fiber Optic Cables Step 24: The
Page 67 and 68: |6. Conduit, Cable Basket and Ladde
Page 69 and 70: 7. Administration| 7. ADMINISTRATIO
Page 71 and 72: 7. Administration| Class 2 Administ
Page 73 and 74: |8. About Anixter SECTION 8: ABOUT
Page 75 and 76: |8. About Anixter Our Technical Exp
Page 77 and 78: |8. About Anixter Supply Chain Solu
Page 79: 12H0014X00 © 2013 Anixter Inc. •

An Installation Pocket Reference Guide.pdf - Anixter

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?