Manual DoorCom IP DCIP 740-0 - Siedle

More documents

Recommendations

Info

5 Installation DCIP 740-... Siedle multi 18 Camera assignment mode Siedle Multi requires additional supply devices which are not listed in this wiring diagram!
DCIP 740-... Siedle multi Functional characteristics Depending on the operating mode camera assignment or monitor assignment, 49 or 4 PC users can be called. Calling, speech and door release via the Software Client DCIP SC 600-... . The Software Client must be installed on every PC which receives door calls. Standard call tones for the Software Client 3-tone chime. A dedicated *.wav file can be assigned for each call tone. It is not possible to listen in to an existing call from other PC users in the network. The door is opened by the called PC user using a “virtual door release button”, the light switching function is actuated using a “virtual light button”. The door call can be muted with an optical display on the monitor. Camera assignment mode The SIM 740-... is assigned to a door / camera. In this mode, the device can be assigned up to 49 different call destinations, i.e. Siedle Multi system addresses which correspond to the functions of 49 Multi telephones. In this operating mode, a DCIP 740-... is required for each door. This operating mode is advisable in systems with a small number of doors and a large number of PC users. Monitor assignment mode: Up to a maximum of 4 call destinations, i.e. Siedle Multi system addresses, can be assigned to the interface. These correspond to the functions of the 4 Multi telephones. The call destination can be dialled from every door within the Siedle Multi (max. 254). This operating mode is advisable in systems with a large number of doors and a small number of PC users. Remarks a) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...) • 12 V AC consumers in the wiring diagram: • Door release appr. 600 mA • Light contact load in the door loudspeaker max. 24 V AC, 2 A c) Distance of the SIVS 610-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 610-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable. Power supply voltage bv+/cv- of the SIVS 610 15 V DC, max. 300 mA When connecting additional devices to the Vario bus (terminals Da/Db), the Vario bus requires an additional power supply. d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the Software Client can still be used. 19
Page 1 and 2: Manual DoorCom IP DCIP 740-0
Page 3 and 4: 1 System description DoorCom IP 740
Page 5 and 6: Monitor assignment mode Commissioni
Page 7 and 8: IP Internet Protocol The IP is a ne
Page 9 and 10: 4 Components for DCIP 740-... Input
Page 11 and 12: 4 Device overview for DCIP 740-...
Page 13 and 14: 5 Terminals CMC 612-0 Block diagram
Page 15 and 16: 5 LED display SIVS 610-... /SIM 740
Page 17: 5 Installation DCIP 740-... Siedle
Page 21 and 22: 6 Configuration SIM 740-... Configu
Page 24 and 25: 6 Configuration software DCIP CO 60
Page 26 and 27: 6 Client-Software DCIP SC 600-... I
Page 28 and 29: 7 Setting the speech volume Level a
Page 30: 10 DoorCom IP FAQ and trouble shoot
Page 33 and 34: 11 Glossary Index Connection 17 As-

Manual DoorCom IP DCIP 740-0 - Siedle

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?