Mechanical Components.pdf - Ken Gilbert

More documents

Recommendations

Info

4-4 [T8E5] DIAGNOSTICS 8. Diagnostics Chart with Trouble Code by ABS Warning Light 8E5 : CHECK TROUBLE CODE. : Is the trouble code 21 and/or 23? : Go to step 8E6. : Go to step 8E7. 8E6 : CHECK HARNESS/CONNECTOR BETWEEN ABSCM&H/U AND ABS SENSOR. 1) Turn ignition switch to OFF. 2) Connect connector to ABS sensor. 3) Measure resistance between ABSCM&H/U connector terminals. Connector & terminal Trouble code 21 / (F49) No. 11 — No. 12: Trouble code 23 / (F49) No. 9 — No. 10: H4M1392A : Is the resistance between 1.0 and 1.5 kΩ? : Go to step 8E8. : Repair harness/connector between ABSCM&H/U and ABS sensor. 32 8E7 : CHECK HARNESS/CONNECTOR BETWEEN ABSCM&H/U AND ABS SENSOR. 1) Turn ignition switch to OFF. 2) Connect connector to ABS sensor. 3) Measure resistance between ABSCM&H/U connector terminals. Connector & terminal Trouble code 25 / (F49) No. 14 — No. 15: Trouble code 27 / (F49) No. 7 — No. 8: H4M1393A : Is the resistance between 0.8 and 1.2 kΩ? : Go to step 8E8. : Repair harness/connector between ABSCM&H/U and ABS sensor.
DIAGNOSTICS 8E8 : CHECK BATTERY SHORT OF HAR- NESS. Measure voltage between ABSCM&H/U connector and chassis ground. Connector & terminal Trouble code 21 / (F49) No. 11 (+) — Chassis ground (−): Trouble code 23 / (F49) No. 9 (+) — Chassis ground (−): Trouble code 25 / (F49) No. 14 (+) — Chassis ground (−): Trouble code 27 / (F49) No. 7 (+) — Chassis ground (−): B4M1240A : Is the voltage less than 1 V? : Go to step 8E9. : Repair harness between ABSCM&H/U and ABS sensor. [T8E11] 4-4 8. Diagnostics Chart with Trouble Code by ABS Warning Light 33 8E9 : CHECK BATTERY SHORT OF HAR- NESS. 1) Turn ignition switch to ON. 2) Measure voltage between ABSCM&H/U connector and chassis ground. Connector & terminal Trouble code 21 / (F49) No. 11 (+) — Chassis ground (−): Trouble code 23 / (F49) No. 9 (+) — Chassis ground (−): Trouble code 25 / (F49) No. 14 (+) — Chassis ground (−): Trouble code 27 / (F49) No. 7 (+) — Chassis ground (−): B4M1240A : Is the voltage less than 1 V? : Go to step 8E10. : Repair harness between ABSCM&H/U and ABS sensor. 8E10 : CHECK INSTALLATION OF ABS SENSOR. Tightening torque: 32±10 N·m (3.3±1.0 kg-m, 24±7 ft-lb) : Are the ABS sensor installation bolts tightened securely? : Go to step 8E11. : Tighten ABS sensor installation bolts securely. 8E11 : CHECK TROUBLE CODE. : Is the trouble code 25 and/or 27? : Go to step 8E12. : Go to step 8E13.
Page 1 and 2:
4-1 [S100] SPECIFICATION AND SERVIC
Page 3 and 4:
4-1 [C100] COMPONENT PARTS 1. Front
Page 5 and 6:
4-1 [C200] COMPONENT PARTS 2. Rear
Page 7 and 8:
4-1 [W1B1] SERVICE PROCEDURE 1. On-
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
4-1 [W2A0] SERVICE PROCEDURE 2. Fro
Page 15 and 16:
4-1 [W2E0] SERVICE PROCEDURE 2. Fro
Page 17 and 18:
Page 19 and 20:
4-1 [W4C2] SERVICE PROCEDURE 4. Fro
Page 21 and 22:
Page 23 and 24:
4-1 [W6B0] SERVICE PROCEDURE 6. Fro
Page 25 and 26:
4-1 [W7B1] SERVICE PROCEDURE 7. Rea
Page 27 and 28:
4-1 [W7E0] SERVICE PROCEDURE 7. Rea
Page 29 and 30:
4-1 [W8B0] SERVICE PROCEDURE 8. Lat
Page 31 and 32:
4-1 [W8E0] SERVICE PROCEDURE 8. Lat
Page 33 and 34:
4-1 [W9B0] SERVICE PROCEDURE 9. Rea
Page 35 and 36:
4-1 [W10B0] SERVICE PROCEDURE 10. R
Page 37 and 38:
4-1 [W11C0] SERVICE PROCEDURE 11. R
Page 39 and 40:
4-1 DIAGNOSTICS MEMO: 40
Page 41 and 42:
3. Front Drive Shaft Assembly Model
Page 43 and 44:
1. Front Axle (1) Baffle plate (SFJ
Page 45 and 46:
1. Front Axle A: REMOVAL 1) Disconn
Page 47 and 48:
3) Remove disc cover from housing.
Page 49 and 50:
11) Attach hub to ST1 securely. 12)
Page 51 and 52:
8) Disconnect parking brake cable e
Page 53 and 54:
12) Remove bolts which secure later
Page 55 and 56:
3) Clean housing interior completel
Page 57 and 58:
10) Bleed air from brake system. 1
Page 59 and 60:
2. REAR DRIVE SHAFT 1) Disconnect g
Page 61 and 62:
8) Place alignment mark on trunnion
Page 63 and 64:
3) Apply a coat of specified grease
Page 65 and 66:
3) Insert DOJ cage onto shaft. NOTE
Page 67 and 68:
CAUTION: Use a new axle nut. Alwa
Page 69 and 70:
5. Steel Wheel and Tire A: INSPECTI
Page 71 and 72:
8. Tire Rotation If tires are maint
Page 73 and 74:
4-3 [S1A0] SPECIFICATIONS AND SERVI
Page 75 and 76:
4-3 [S1C0] SPECIFICATIONS AND SERVI
Page 77 and 78:
4-3 [C200] COMPONENT PARTS 2. Power
Page 79 and 80:
4-3 [C300] COMPONENT PARTS 3. Power
Page 81 and 82:
4-3 [W2B0] SERVICE PROCEDURE 2. Til
Page 83 and 84:
4-3 [W2D0] SERVICE PROCEDURE 2. Til
Page 85 and 86:
4-3 [W3A0] SERVICE PROCEDURE 3. Ste
Page 87 and 88:
4-3 [W3C0] SERVICE PROCEDURE 3. Ste
Page 89 and 90:
4-3 [W3C3] SERVICE PROCEDURE 3. Ste
Page 91 and 92:
4-3 [W3D0] SERVICE PROCEDURE 3. Ste
Page 93 and 94:
4-3 [W3F0] SERVICE PROCEDURE 3. Ste
Page 95 and 96:
4-3 [W4B0] SERVICE PROCEDURE 4. Con
Page 97 and 98:
4-3 [W4C2] SERVICE PROCEDURE 4. Con
Page 99 and 100:
4-3 [W4D1] SERVICE PROCEDURE 4. Con
Page 101 and 102:
4-3 [W5A0] SERVICE PROCEDURE 5. Pip
Page 103 and 104:
4-3 [W5C0] SERVICE PROCEDURE 5. Pip
Page 105 and 106:
4-3 [W6A0] SERVICE PROCEDURE 6. Oil
Page 107 and 108:
4-3 [W6B1] SERVICE PROCEDURE 6. Oil
Page 109 and 110:
4-3 [W6D0] SERVICE PROCEDURE 6. Oil
Page 111 and 112:
4-3 [W6E0] SERVICE PROCEDURE 6. Oil
Page 113 and 114:
4-3 [W7A0] SERVICE PROCEDURE 7. Pow
Page 115 and 116:
4-3 [K1B0] DIAGNOSTICS 1. Power Ste
Page 117 and 118:
4-3 [K1C0] DIAGNOSTICS 1. Power Ste
Page 119 and 120:
4-3 [K1C0] DIAGNOSTICS 1. Power Ste
Page 121 and 122:
4-3 [K1E0] DIAGNOSTICS 1. Power Ste
Page 123 and 124:
4-3 [K1F0] DIAGNOSTICS 1. Power Ste
Page 125 and 126:
4-3 DIAGNOSTICS MEMO: 54
Page 127 and 128:
2. 2500 cc MODEL SPECIFICATIONS AND
Page 129 and 130:
1. Front Disc Brake A: EXCEPT 2500
Page 131 and 132:
2. Rear Disc Brake (1) Caliper body
Page 133 and 134:
4. Master Cylinder A: WITH ABS VEHI
Page 135 and 136:
5. Brake Booster A: MODELS WITH ABS
Page 137 and 138:
B: ABS CONTROL MODULE AND HYDRAULIC
Page 139 and 140:
1. Front Disc Brake A: ON-CAR SERVI
Page 141 and 142:
5) Remove disc rotor from hub. NOTE
Page 143 and 144:
1) Clean mud and foreign particles
Page 145 and 146:
1) Clean mud and foreign particles
Page 147 and 148:
F: INSTALLATION 1) Install disc rot
Page 149 and 150:
B: REMOVAL (1) Caliper body (2) Air
Page 151 and 152:
E: ASSEMBLY 1) Clean caliper body i
Page 153 and 154:
NOTE: If it is difficult to remove
Page 155 and 156:
D: ASSEMBLY 1. WHEEL CYLINDER 1) Cl
Page 157 and 158:
4. Parking Brake (Rear Disc Brake)
Page 159 and 160:
D: ADJUSTMENT 1. SHOE CLEARANCE 1)
Page 161 and 162:
6. Brake Booster A: REMOVAL 1) Remo
Page 163 and 164:
3. OPERATION CHECK 1) With engine o
Page 165 and 166:
7) While holding hexagonal part of
Page 167 and 168:
11) Remove bolt and clamp from rear
Page 169 and 170:
11. Brake Fluid A: REPLACEMENT CAUT
Page 171 and 172:
CAUTION: Do not disassemble or adju
Page 173 and 174:
3. OUTPUT VOLTAGE Output voltage ca
Page 175 and 176:
14. ABS Control Module and Hydrauli
Page 177 and 178:
9) Remove air bleeder screws from t
Page 179 and 180:
SERVICE PROCEDURE 4. CONDITIONS FOR
Page 181 and 182:
15B2 : CHECK G SENSOR. Measure volt
Page 183 and 184:
1. Entire Brake System DIAGNOSTICS
Page 185 and 186:
4-5 [S100] SPECIFICATIONS AND SERVI
Page 187 and 188:
4-5 [C1A2] COMPONENT PARTS 1. Pedal
Page 189 and 190:
4-5 [W1A1] SERVICE PROCEDURE 1. Ped
Page 191 and 192:
4-5 [W1A4] SERVICE PROCEDURE 1. Ped
Page 193 and 194:
4-5 [W1C1] SERVICE PROCEDURE 1. Ped
Page 195 and 196:
4-5 [W1F1] SERVICE PROCEDURE 1. Ped
Page 197 and 198:
4-5 [W3A0] SERVICE PROCEDURE 3. Acc
Page 199 and 200:
4-5 [K100] DIAGNOSTICS 1. Pedal Sys
Page 201 and 202:
1. Heater Unit (1) Vent door (2) DE
Page 203 and 204:
3. Control Unit (1) Temperature con
Page 205 and 206:
3. Blower Motor Assembly A: REMOVAL
Page 207 and 208:
4-7 [S100] SPECIFICATIONS 1. Specif
Page 209 and 210:
4-7 [C200] COMPONENT PARTS 2. Intak
Page 211 and 212:
4-7 [W1A0] SERVICE PROCEDURE 1. Saf
Page 213 and 214:
4-7 [W300] SERVICE PROCEDURE 3. Too
Page 215 and 216:
4-7 [W300] SERVICE PROCEDURE 3. Too
Page 217 and 218:
4-7 [W4D0] SERVICE PROCEDURE 4. O-r
Page 219 and 220:
4-7 [W600] SERVICE PROCEDURE 6. Dis
Page 221 and 222:
4-7 [W7C0] SERVICE PROCEDURE 7. Eva
Page 223 and 224:
4-7 [W8A0] SERVICE PROCEDURE 8. Lea
Page 225 and 226: 4-7 [W8A7] SERVICE PROCEDURE 9. Lub
Page 227 and 228: 4-7 [W11B0] SERVICE PROCEDURE 11. C
Page 229 and 230: 4-7 [W11C0] SERVICE PROCEDURE 11. C
Page 231 and 232: 4-7 [W13A0] SERVICE PROCEDURE 13. R
Page 233 and 234: 4-7 [W15A0] SERVICE PROCEDURE 15. C
Page 235 and 236: 4-7 [W17B0] SERVICE PROCEDURE 18. P
Page 237 and 238: 4-7 [K200] DIAGNOSTICS 2. Performan
Page 239 and 240: 4-7 [K200] DIAGNOSTICS 2. Performan
Page 241 and 242: 4-7 [K400] DIAGNOSTICS 4. Compresso
Page 243 and 244: 4-7 [K600] DIAGNOSTICS 6. Radiator
Page 245 and 246: 4-7 [K800] DIAGNOSTICS 8. Condenser
Page 247 and 248: B: ELECTRICAL INSPECTION DIAGNOSTIC
Page 249 and 250: B4M1226B H4M1304A S4M0055A B4M2201C
Page 251 and 252: MEMO: DIAGNOSTICS 7 [T400] 4-4 4. S
Page 253 and 254: ABS sensor*2 (Wheel speed sensor) C
Page 255 and 256: 6. Diagnostics Chart for On-board D
Page 257 and 258: Behavior of vehicle a) Directional
Page 259 and 260: 1. CALLING UP A TROUBLE CODE 1) Tak
Page 261 and 262: MEMO: [T6D2] 4-4 DIAGNOSTICS 6. Dia
Page 263 and 264: 7A1 : CHECK IF OTHER WARNING LIGHTS
Page 265 and 266: 7A10 : CHECK POOR CONTACT IN CON- N
Page 267 and 268: 7B1 : CHECK INSTALLATION OF ABSCM&H
Page 269 and 270: 7B10 : CHECK WIRING HARNESS. Measur
Page 271 and 272: 7C1 : CHECK DIAGNOSIS TERMINAL. Mea
Page 273 and 274: 8. Diagnostics Chart with Trouble C
Page 275: 8E1 : CHECK FRONT ABS SENSOR. 1) Tu
Page 279 and 280: DIAGNOSTICS 8E16 : CHECK GROUND SHO
Page 281 and 282: 8I1 : CHECK INSTALLATION OF ABS SEN
Page 283 and 284: 8I10 : CHECK RESISTANCE OF FRONT AB
Page 285 and 286: 8I16 : CHECK GROUND SHORT OF HAR- N
Page 287 and 288: MEMO: DIAGNOSTICS [T8I23] 4-4 8. Di
Page 289 and 290: 8J1 : CHECK IF THE WHEELS HAVE TURN
Page 291 and 292: MEMO: DIAGNOSTICS [T8J14] 4-4 8. Di
Page 293 and 294: 8N1 : CHECK INPUT VOLTAGE OF ABSCM&
Page 295 and 296: 8R1 : CHECK INPUT VOLTAGE OF ABSCM&
Page 297 and 298: 8S1 : CHECK GROUND CIRCUIT OF ABSCM
Page 299 and 300: 8T1 : CHECK GENERATOR. 1) Start eng
Page 301 and 302: MEMO: DIAGNOSTICS [T8T7] 4-4 8. Dia
Page 303 and 304: 8U1 : CHECK SPECIFICATIONS OF THE A
Page 305 and 306: 8U10 : CHECK ANY OTHER TROUBLE CODE
Page 307 and 308: 8V1 : CHECK INPUT VOLTAGE OF ABSCM&
Page 309 and 310: MEMO: DIAGNOSTICS [T8V6] 4-4 8. Dia
Page 311 and 312: 8W1 : CHECK INPUT VOLTAGE OF ABSCM&
Page 313 and 314: MEMO: DIAGNOSTICS [T8W8] 4-4 8. Dia
Page 315 and 316: 8X1 : CHECK STOP LIGHTS COME ON. De
Page 317 and 318: 8Y1 : CHECK ALL FOUR WHEELS FOR FRE
Page 319 and 320: DIAGNOSTICS 8Y8 : CHECK GROUND SHOR
Page 321 and 322: MEMO: DIAGNOSTICS [T8Y14] 4-4 8. Di
Page 323 and 324: 6. FREEZE FRAME DATA NOTE: Data st
Page 325 and 326: B: LIST OF DIAGNOSTIC TROUBLE CODE
Page 327 and 328:
10C1 : CHECK IGNITION SWITCH. : Is
Page 329 and 330:
MEMO: DIAGNOSTICS 85 [T10C9] 4-4 10
Page 331 and 332:
10D1 : CHECK WIRING HARNESS. 1) Tur
Page 333 and 334:
MEMO: DIAGNOSTICS 89 [T10D6] 4-4 10
Page 335 and 336:
WIRING DIAGRAM: DIAGNOSTICS 91 [T10
Page 337 and 338:
10H7 : CHECK POOR CONTACT IN CON- N
Page 339 and 340:
DIAGNOSTICS 10H16 : CHECK HARNESS/C
Page 341 and 342:
10H23 : CHECK HUB RUNOUT. Measure h
Page 343 and 344:
MEMO: DIAGNOSTICS 99 [T10H28] 4-4 1
Page 345 and 346:
10L1 : CHECK OUTPUT OF ABS SENSOR U
Page 347 and 348:
10L13 : CHECK ABS SENSOR SIGNAL. DI
Page 349 and 350:
DIAGNOSTICS 10L21 : CHECK HARNESS/C
Page 351 and 352:
10L28 : CHECK SHIELD CIRCUIT. DIAGN
Page 353 and 354:
10M1 : CHECK IF THE WHEELS HAVE TUR
Page 355 and 356:
MEMO: DIAGNOSTICS 111 [T10M14] 4-4
Page 357 and 358:
10Q1 : CHECK INPUT VOLTAGE OF ABSCM
Page 359 and 360:
10U1 : CHECK INPUT VOLTAGE OF ABSCM
Page 361 and 362:
10V1 : CHECK GROUND CIRCUIT OF ABSC
Page 363 and 364:
10W1 : CHECK GENERATOR. 1) Start en
Page 365 and 366:
MEMO: DIAGNOSTICS 121 [T10W7] 4-4 1
Page 367 and 368:
10X1 : CHECK GENERATOR. 1) Start en
Page 369 and 370:
MEMO: DIAGNOSTICS 125 [T10X7] 4-4 1
Page 371 and 372:
10Y1 : CHECK SPECIFICATIONS OF THE
Page 373 and 374:
MEMO: DIAGNOSTICS 129 [T10Y8] 4-4 1
Page 375 and 376:
DIAGNOSTICS 10Z1 : CHECK BATTERY SH
Page 377 and 378:
MEMO: DIAGNOSTICS 133 [T10Z6] 4-4 1
Page 379 and 380:
10AA1 : CHECK INPUT VOLTAGE OF ABSC
Page 381 and 382:
10AB1 : CHECK VALVE RELAY IN ABSCM&
Page 383 and 384:
10AC1 : CHECK INPUT VOLTAGE OF ABSC
Page 385 and 386:
10AD1 : CHECK MOTOR RELAY IN ABSCM&
Page 387 and 388:
10AE1 : CHECK INPUT VOLTAGE OF ABSC
Page 389 and 390:
MEMO: DIAGNOSTICS 145 [T10AE8] 4-4
Page 391 and 392:
10AF1 : CHECK OUTPUT OF STOP LIGHT
Page 393 and 394:
MEMO: DIAGNOSTICS 149 [T10AF7] 4-4
Page 395 and 396:
10AG1 : CHECK OUTPUT OF G SENSOR US
Page 397 and 398:
10AG9 : CHECK G SENSOR. Measure vol
Page 399 and 400:
10AH1 : CHECK OUTPUT OF G SENSOR US
Page 401 and 402:
10AH15 : CHECK OPEN CIRCUIT IN G SE
Page 403 and 404:
10AH21 : CHECK POOR CONTACT IN CONN
Page 405 and 406:
10AI1 : CHECK OUTPUT OF G SENSOR US
Page 407 and 408:
10AI10 : CHECK ABSCM&H/U. 1) Turn i
Page 409 and 410:
10AJ1 : CHECK ALL FOUR WHEELS FOR F
Page 411 and 412:
10AJ10 : CHECK G SENSOR. Measure vo
Page 413 and 414:
B: CHECKING THE HYDRAULIC UNIT OPER
show all

Mechanical Components.pdf - Ken Gilbert

Create successful ePaper yourself

Delete template?

Save as template?