Smart Infrared Inspection System Field Operational Test - Center for ...

More documents

Recommendations

Info

TEMPERATURE DISPLAY BOX The temperature display box presents the gathered data to the operator. The data is identified by the side and axle number. The temperature below that identifier is the number for that axle, side and component. To change which component of the wheel is being feature in the Temperature Display Box, see below. More information on using the information displayed here is available in the Alerts section of this manual. TEMPERATURE DISPLAY MENU The temperature display menu allows the operator to change the data group that is being displayed. By clicking on the drop down menu, the operator can switch between the three components that are measured by SIRIS: tire, brake, or bearing. The information that the operator looks at should be determined by the issued alert. The default for this menu is brake. REALTIME UPDATES This drop down menu is used to set when the system updates the image window. The screen could update with new images for every vehicle is measured as it is measured, only when an alert is issued while a vehicle is being measured, or not at all. The operator may wish to turn the updates off while studying a previously collected file as the update will remove the previous inspection images from the screen. If the updates are set to On, every new vehicle will cause the screen to update. If the Alerts Only is chosen, the screen updates only when a problem is detected with a passing vehicle. All files are saved regardless of the setting for Realtime Updates. 48
CONNECT This button allows the operator to connect the user interface computer to the Main Unit and begin a session. This function is detailed in the Getting Started section of this manual. DISCONNECT Clicking on Disconnect will end the session and will disconnect the user interface computer from the Main Unit. More detail on this can be found in the Getting Started section of this manual. START COLLECTING Once connected, the user must select ‘Start Collecting’ in order to begin a new session. The system will not image any vehicles passing through the system until ‘Start Collecting’ is selected and the cameras have had a few moments to start. This is detailed in the Getting Started section of this manual. STOP COLLECTING If the operator wishes to stop collecting data, Stop Collecting’ is chosen. The system will no longer measure or collect data from passing vehicles. This is often used if the inspection site is already full. The Getting Started section has more detail on this function. 49
Page 1 and 2:
ORNL/TM-2011/98 Smart Infrared Insp
Page 3 and 4:
Energy and Transportation Science D
Page 5 and 6:
TABLE OF CONTENTS ABBREVIATIONS, AC
Page 7 and 8: LIST OF FIGURES Figure 1. Driver's
Page 9 and 10: EXECUTIVE SUMMARY The Smart InfraRe
Page 11 and 12: 1. INTRODUCTION In 2006, Internatio
Page 13 and 14: Type of Flaw Detected Brakes 274 Ti
Page 15 and 16: 2. FIELD OPERATIONAL TEST The FOT w
Page 17 and 18: Figure 1. Driver's side components
Page 19 and 20: 2.2.2 Performance-Based Brake Teste
Page 21 and 22: 3. ANALYSIS OF FOT DATA The main go
Page 23 and 24: Type of Flaw Detected Table 5. Deta
Page 25 and 26: Percentage of Sampled Vehicles Perc
Page 27 and 28: 3.3.3 Bearing Violations Shown in T
Page 29 and 30: 4.1 SIRIS FUNCTIONALITY ISSUES 4. L
Page 31 and 32: 5. CONCLUSIONS The SIRIS device dev
Page 33 and 34: 6. FUTURE DIRECTION Based on the da
Page 35 and 36: ACKNOWLEDGEMENTS The CMVRTC team wo
Page 37 and 38: APPENDIX A: MAINLINE BRAKE ASSESSME
Page 39 and 40: APPENDIX B: VIOLATIONS ASSOCIATED W
Page 41 and 42: APPENDIX C: SIRIS PROBLEM LOG SHEET
Page 43 and 44: APPENDIX D: SIRIS FIELD OPERATIONAL
Page 45 and 46: APPENDIX E: TENNESSEE HIGHWAY PATRO
Page 47 and 48: APPENDIX F: SIRIS OPERATIONS MANUAL
Page 49 and 50: InfraRed Camera Optical Trigger Veh
Page 51 and 52: REGIONS OF INTEREST SIRIS measures
Page 53 and 54: If the ROI is too skewed, it will c
Page 55 and 56: STOP COLLECTING In order to stop co
Page 57: MODULE STATUS Module status lists t
Page 61 and 62: DISPLAY vehicle entries in the coll
Page 63 and 64: AUTO SCALE Auto Scale adjusts the c
Page 65 and 66: ALERTING SYSTEM When the SIRIS syst
Page 67 and 68: TIRE ALERTS As a vehicle passes thr
Page 69 and 70: It is recommended that vehicles wit
Page 71 and 72: BEARING ALERTS Bearing alerts are i
show all

Smart Infrared Inspection System Field Operational Test - Center for ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?