GCS Satellite Hardware Manual - Galaxy Control Systems

More documents

Recommendations

Info

Dial Line jack is RJ-45 same DTE Options Async Data same Make DTE Rate same on both modems 8 Bit char size same No Parity same Ignores DTR same DCD is normal same CTS follows RTS same RTS-CTS delay is 0ms same DTE Fallback-disabled same Black Box 201 BC/AS Analog leased lines can also be used for the Network Bridge. The settings below designate how the switches and jumpers need to be set for the Black Box 201BC/AS devices to function properly. Analog lines can only communicate at 2400 baud so set the Satellite CPU baud rate accordingly. S1: 1,4,6,8 up S2: 2 up S3: none up E2: E3 CGND E4: RX E5: Out E6: For test -12 Normally 0 E7: B E8: B E9: OUT E10: IN E11: -45 E12: B E13: E14: D E15: D When testing the modems locally, use the following connections for the RJ-45 cable between the modems: pin 3 to pin 4; pin 4 to pin 3; pin 5 to pin 6; pin 6 to pin 5 US Robotics Courier V. Everything A standard US robotics Courier modem may be used for certain applications of the Network Bridge. The following AT commands need to be sent to the modem at the Remote Primary ATS13=16&W At Power on or Reset this dials the number of the extending secondary stored at position 0 AT&Z0=number&W Store phone number of the extending secondary at position 0. AT&B1&W Fixes serial communication rate 38 Satellite Installation Manual
AT&N=6 Sets maximum connection rate. 6=9600 baud; 4=4800; 3=2400 Modem Switch Settings: Extending Secondary: 1,2,4,5,6,7, and 9 up Remote Primary: 1,2,4,6,7,9 and 10 up Controller to Modem cable: 2 3 4 5 6 7 8 1 to 3 2 4 5 6 7 8 20 Satellite Installation Manual 39
Page 1 and 2: Installation Manual Version 1.3 Nov
Page 3 and 4: Table of Contents TABLE OF CONTENTS
Page 5 and 6: Introduction Overview Satellite is
Page 7 and 8: - 2 GB of free hard drive space to
Page 9 and 10: Controller Installation Site Plan T
Page 11 and 12: Mounting the Controller The control
Page 13 and 14: Unit Number Switches (S2) To the im
Page 15 and 16: Switches 7 and 8 - are unused at th
Page 17 and 18: Port Configuration Each port on a S
Page 19 and 20: Pin 5: This is Data 0 for the reade
Page 21 and 22: alarm partitions. Only Galaxy Contr
Page 23 and 24: System’s Infrared format readers
Page 25 and 26: Alarms cannot be Armed or Disarmed
Page 27 and 28: Parallel Reader Module In certain c
Page 29 and 30: not done, once the readers are powe
Page 31 and 32: Voltage jumper There is a voltage j
Page 33 and 34: pulled low by the controller when t
Page 35 and 36: shield attached to ground at one en
Page 37: Figure 26 There are several differe
Page 41 and 42: While at the controller location, b
Page 43 and 44: 1. Use the CD to install EZWebCon o
Page 45 and 46: 10. Type in SYSTEM as the password
Page 47 and 48: 4. Open EZWebCon. (Start button >>
Page 49 and 50: 12. The IP configuration will now b
Page 51 and 52: Appendix Unit Number Table 0 = Swit
Page 53: Switch # 1 2 3 4 5 6 7 8 Value 1 2

GCS Satellite Hardware Manual - Galaxy Control Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?