Monza 24 and 28 Instructions for use - Heatline

More documents

Recommendations

Info

15.4.2 Domestic Hot Water 16 Gas conversion adjustments Conversion of this appliance to run on LPG requires a conversion kit . The kit and the conversion operation must be done by the Heatline Service Team, please ring : 0844 736 9042 . Please note that if the appliance requires conversion, the installer should be qualifi ed by Gas Safe Register to install LPG appliances in order to complete the installation and its notifi cation after conversion has been done. - 32 - Service Call 0844 736 9042, Technical Help (Chargeable) Call 0906 802 0253
17 Draining 17.1 Heating circuit • To obtain service, please call your installer or Heatline’s own service organisation. PLEASE NOTE: During routine servicing, and after any maintenance, we recommend that the following must be checked: - The integrity of the fl ue system and the fl ue seals, - The integrity of the boiler combustion circuit and the relevant seals, - The operational (working) gas inlet pressure at maximum rate, Key 1 Length of hose (not supplied) 2 Drain valve • Drain down the heating circuit of the boiler only, by closing the heating fl ow and return isolating valves. See chapter "Hydraulic connection ► Gas and water connections" • Attach a length of hose (1) to the drain point and open the drain valve (2). • After draining, close the drain valve (2) and remove the hose. 17.2 Domestic Hot water circuit • Drain the Domestic Hot Water circuit by closing the coldwater isolation valve. • Open one or more hot water taps to drain the hot water circuit. 18 Servicing • To ensure the continued effi cient and safe operation of the boiler it is recommended that it is checked and serviced as necessary at regular intervals. The frequency of servicing will depend upon the particular installation conditions and usage. If this appliance is installed in a rented property there is a duty of care imposed on the owner of the property by the current issue of the Gas Safety (Installation and Use) Regulations, Section 35. • Servicing/maintenance should be carried out by a competent person approved at the time by the Health and Safety Executive in accordance with the rules in force in the countries of destination. 2 A B 2 1 - The gas rate, - The combustion performance. • See the "Safety instructions" chapter for a list of operations to be performed prior to the maintenance of the application. • Once the maintenance operations have been completed, consult the ¨Start Up¨ chapter to restart the appliance. 18.1 Annual Maintenance 18.1.1 Verification of components • Check that the fl ow sensor is working properly. See chapter "Specifi c adjustment ► Appliance technical settings and parameter list ► Installation settings" and use code “d.36”. • Check that the fan is working properly. See chapter "Specifi c adjustment ► Appliance technical settings and parameter list ► Installation settings" and use code “d.34”. • Check that the temperature sensors are working properly. See chapter "Specifi c adjustment ► Appliance technical settings and parameter list ► Installation settings" and use code “d.3, d.4, d.40, d.41”. • Check the ionisation quality. • Check that the thermal fuse protects the appliance against dry fi re. Disconnect the thermal fuse and check if "F76" fault code is displayed on the screen. • Check that the pressure sensor is working properly. The pressure must be displayed on the screen. • Check the pressure of the expansion vessel. 18.1.2 Other checks • Check the CO 2 and fuel rate and compare them with the values in the chapter “CO 2 Measurement” If the fl ame picture and combustion is OK then there is no need to remove the combustion box door, continue with the checks below. Should the combustion be out of range continue with a full service noting that should the combustion chamber be opened then the graphite seal (12) and the locking nuts (7) as seen in diagram 18.9 should be replaced. • Check that there are no leaks in the joints and the safety valves. Service Call 0844 736 9042, Technical Help (Chargeable) Call 0906 802 0253 - 33 -
Page 1 and 2: Monza Installation and Servicing Mo
Page 3 and 4: INTRODUCTION 1 Instructions guidanc
Page 5 and 6: 19 Ignition module 20 Heating flow
Page 7 and 8: 4.2 Appliance Most of the appliance
Page 9 and 10: 7 Appliance installation 7.1 Scope
Page 11 and 12: The fl ue is designed with an inter
Page 13 and 14: Service Call 0844 736 9042, Technic
Page 15 and 16: 9 Evacuation of combustion products
Page 17 and 18: 9.2 Flue configuration description
Page 19 and 20: 230V permanent supply + 230V system
Page 21 and 22: 11 Commissioning At the time of com
Page 23 and 24: Operational Gas Inlet Pressure In c
Page 25 and 26: 13 Installation settings • To adj
Page 27 and 28: 13.1.2 Test modes By activating the
Page 29 and 30: 15.1.2 Check the gas supply 1 15.2
Page 31: Fault codes Description Cause Solut
Page 35 and 36: 2A Flue elbow 2B Vertical flue adap
Page 37 and 38: 18.8 Condensate trap a Warning: 3 5
Page 39 and 40: 18.9.1 Spark electrode • Disconne
Page 41 and 42: 19.4 Hydraulic block 31 32 33 34 9
Page 43 and 44: 19.5 Combustion block 19 20 21 18 1
Page 45 and 46: When reconnecting, the polarity of
Page 47 and 48: 20 Spare parts In order to guarante
Page 50 and 51: Failure to install and commission a
Page 52: 0020112884-03 06/11 Heatline, Notti

Monza 24 and 28 Instructions for use - Heatline

Create successful ePaper yourself

Delete template?

Save as template?