Frequency converter FKO - Brinkmann Pumps

More documents

Recommendations

Info

Important information means of a risk assessment for the machine or system and its electrical equipment, and is determined with a selection of the circuit category according to DIN EN 13849 “Safety of machinery – Safety-related parts of control systems”. 1.7 Contacts for information Further information is available from: Tel: +49 2392 5006-0 Monday to Friday: 7.00 to 17.00 (local time) Fax: +49 2392 5006-180 Email: Sales@BrinkmannPumps.de Internet address Customers can access technical and general information from the following address: http://www.BrinkmannPumps.com 14 Operating manual FKO
2 Overview of the drive control Overview of the drive control This chapter contains information on the scope of delivery for the drive control and the function description. 2.1 Description of the FKO drive control The FKO drive control is a device for speed control in three-phase a.c. motors. The drive control can be integrated in the motor (with the standard adapter plate) or close to the motor (with the wall installation adapter plate). The permitted ambient temperatures specified under Technical data refer to operation at nominal load. In many cases of application, higher temperatures may be permitted after a detailed technical analysis. These have to be approved by BRINKMANN for each individual case. 3 Installation 3.1 Safety instructions during installation WARNING � Installation may be performed only be appropriately qualified employees who are trained in the set-up, installation, start-up and operation of the product. Work performed on the drive control by unqualified staff and non-observance of warnings can result in serious injury or damage. � The device must be grounded in accordance with DIN EN 61140; VDE 0140, NEC and other relevant standards. Mains connections must be hardwired. Operating manual FKO 15
Page 1 and 2: Operating manual Frequency converte
Page 3 and 4: Table of contents 1 Important infor
Page 5 and 6: Overview of installation sizes Dime
Page 7 and 8: Important information Supplemental
Page 9 and 10: Important information ATTENTION! Pl
Page 11 and 12: 1.4.4 Operation WARNING Important i
Page 13: 1.5 Proper use Important informatio
Page 17 and 18: Installation 3.2.2 Suitable install
Page 19 and 20: 3.2.5 Wiring instructions Installat
Page 21 and 22: 3.3.2 Connections for brake resisto
Page 23 and 24: Terminal no. Designation Configurat
Page 25 and 26: Installation The following figure s
Page 27 and 28: Fig. 8: Fastening the adapter plate
Page 29 and 30: Installation 5. Wire the motor cabl
Page 31 and 32: 4 Commissioning 4.1 Safety instruct
Page 33 and 34: 4.3 Block diagram Internal potentio
Page 35 and 36: 5 Parameters Parameters This chapte
Page 37 and 38: Stand-by function in PID process co
Page 39 and 40: 5.2.2 Structure of the parameter ta
Page 41 and 42: 1.051 Acceleration 1 Unit: s Relati
Page 43 and 44: 1.130 Reference channel Unit: integ
Page 45 and 46: 1.180 Reset Unit: integer Relations
Page 47 and 48: 5.3.3 Motorized potentiometer Param
Page 49 and 50: 3.052 PID derivative gain Unit: s R
Page 51 and 52: 5.3.5 Analogue inputs For analogue
Page 53 and 54: 4.034/4.064 Alx physical minimum Un
Page 55 and 56: 5.3.8 Digital outputs For digital o
Page 57 and 58: 4.191/4.211 Rel.x on Unit: Relation
Page 59 and 60: Parameters The entire function can
Page 61 and 62: 33.032 Motor power Unit: W Relation
Page 63 and 64: 5.4.2 I 2 T 33.010 I 2 T fact. moto
Page 65 and 66:
34.011 Type of encoder Unit: intege
Page 67 and 68:
5.4.5 Squared characteristic 34.120
Page 69 and 70:
Error detection and troubleshooting
Page 71 and 72:
Error detection and troubleshooting
Page 73 and 74:
7 Technical data 7.1 General data T
Page 75 and 76:
8 Optional accessories This chapter
Page 77 and 78:
=== Ende der Liste für Textmarke I
Page 79 and 80:
Notes
Page 81 and 82:
R Reference channel............ 42,
show all

Frequency converter FKO - Brinkmann Pumps

Create successful ePaper yourself

Delete template?

Save as template?